[prev in list] [next in list] [prev in thread] [next in thread]
List: openocd-development
Subject: [PATCH]: 3b006c00e0 Add configs for Espressif RISC-V targets.
From: gerrit () openocd ! org
Date: 2024-05-12 19:54:01
Message-ID: 20240512195402.07E8EEB () openocd ! org
[Download RAW message or body]
This is an automated email from Gerrit.
"Bernhard Rosenkränzer <bero@baylibre.com>" just uploaded a new patch set to Gerrit, \
which you can find at https://review.openocd.org/c/openocd/+/8263
-- gerrit
commit 3b006c00e01774229edab54833862bbbada9726b
Author: Bernhard Rosenkränzer <bero@baylibre.com>
Date: Sun May 12 21:47:21 2024 +0200
Add configs for Espressif RISC-V targets.
This adds configs for ESP32-C2, ESP32-C3, ESP32-C6 and ESP-H2.
This is based on the work of Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I23039d09252cb8a6d2fba6581733efc58e8061ce
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
diff --git a/tcl/board/esp32c2-ftdi.cfg b/tcl/board/esp32c2-ftdi.cfg
new file mode 100644
index 0000000000..bc2b82f5aa
--- /dev/null
+++ b/tcl/board/esp32c2-ftdi.cfg
@@ -0,0 +1,21 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+#
+# Example OpenOCD configuration file for ESP32-C2 connected via ESP-Prog.
+#
+# For example, OpenOCD can be started for ESP32-C2 debugging on
+#
+# openocd -f board/esp32c2-ftdi.cfg
+#
+
+# Source the JTAG interface configuration file
+source [find interface/ftdi/esp32_devkitj_v1.cfg]
+# Source the ESP32-C2 configuration file
+source [find target/esp32c2.cfg]
+
+# The speed of the JTAG interface, in kHz. If you get DSR/DIR errors (and they
+# do not relate to OpenOCD trying to read from a memory range without physical
+# memory being present there), you can try lowering this.
+#
+# On DevKit-J, this can go as high as 20MHz if CPU frequency is 80MHz, or 26MHz
+# if CPU frequency is 160MHz or 240MHz.
+adapter speed 20000
diff --git a/tcl/board/esp32c3-builtin.cfg b/tcl/board/esp32c3-builtin.cfg
new file mode 100644
index 0000000000..9e19b1b93c
--- /dev/null
+++ b/tcl/board/esp32c3-builtin.cfg
@@ -0,0 +1,15 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+#
+# Example OpenOCD configuration file for ESP32-C3 connected via builtin USB-JTAG \
adapter. +#
+# For example, OpenOCD can be started for ESP32-C3 debugging on
+#
+# openocd -f board/esp32c3-builtin.cfg
+#
+
+# Source the JTAG interface configuration file
+source [find interface/esp_usb_jtag.cfg]
+# Source the ESP32-C3 configuration file
+source [find target/esp32c3.cfg]
+
+adapter speed 40000
diff --git a/tcl/board/esp32c3-ftdi.cfg b/tcl/board/esp32c3-ftdi.cfg
new file mode 100644
index 0000000000..55953742c4
--- /dev/null
+++ b/tcl/board/esp32c3-ftdi.cfg
@@ -0,0 +1,21 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+#
+# Example OpenOCD configuration file for ESP32-C3 connected via ESP-Prog.
+#
+# For example, OpenOCD can be started for ESP32-C3 debugging on
+#
+# openocd -f board/esp32c3-ftdi.cfg
+#
+
+# Source the JTAG interface configuration file
+source [find interface/ftdi/esp32_devkitj_v1.cfg]
+# Source the ESP32-C3 configuration file
+source [find target/esp32c3.cfg]
+
+# The speed of the JTAG interface, in kHz. If you get DSR/DIR errors (and they
+# do not relate to OpenOCD trying to read from a memory range without physical
+# memory being present there), you can try lowering this.
+#
+# On DevKit-J, this can go as high as 20MHz if CPU frequency is 80MHz, or 26MHz
+# if CPU frequency is 160MHz or 240MHz.
+adapter speed 20000
diff --git a/tcl/board/esp32c6-builtin.cfg b/tcl/board/esp32c6-builtin.cfg
new file mode 100644
index 0000000000..abc96b2d14
--- /dev/null
+++ b/tcl/board/esp32c6-builtin.cfg
@@ -0,0 +1,15 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+#
+# Example OpenOCD configuration file for ESP32-C6 connected via builtin USB-JTAG \
adapter. +#
+# For example, OpenOCD can be started for ESP32-C6 debugging on
+#
+# openocd -f board/esp32c6-builtin.cfg
+#
+
+# Source the JTAG interface configuration file
+source [find interface/esp_usb_jtag.cfg]
+# Source the ESP32-C6 configuration file
+source [find target/esp32c6.cfg]
+
+adapter speed 40000
diff --git a/tcl/board/esp32h2-builtin.cfg b/tcl/board/esp32h2-builtin.cfg
new file mode 100644
index 0000000000..e98d1faf4f
--- /dev/null
+++ b/tcl/board/esp32h2-builtin.cfg
@@ -0,0 +1,15 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+#
+# Example OpenOCD configuration file for ESP32-H2 connected via builtin USB-JTAG \
adapter. +#
+# For example, OpenOCD can be started for ESP32-H2 debugging on
+#
+# openocd -f board/esp32h2-builtin.cfg
+#
+
+# Source the JTAG interface configuration file
+source [find interface/esp_usb_jtag.cfg]
+# Source the ESP32-C3 configuration file
+source [find target/esp32h2.cfg]
+
+adapter speed 40000
diff --git a/tcl/target/esp32c2.cfg b/tcl/target/esp32c2.cfg
new file mode 100644
index 0000000000..42aeb0adea
--- /dev/null
+++ b/tcl/target/esp32c2.cfg
@@ -0,0 +1,117 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+#
+
+# Source the ESP common configuration file.
+source [find target/esp_common.cfg]
+
+# Target specific global variables
+set _CHIPNAME "riscv"
+set _CPUTAPID 0x0000cc25
+set _ESP_ARCH "riscv"
+set _ONLYCPU 1
+set _ESP_SMP_TARGET 0
+set _ESP_SMP_BREAK 0
+set _ESP_EFUSE_MAC_ADDR_REG 0x60008840
+
+# Target specific functions should be implemented for each riscv chips.
+proc riscv_wdt_disable { } {
+ # Halt event can occur during config phase (before "init" is done).
+ # Ignore it since mww commands don't work at that time.
+ if { [string compare [command mode] config] == 0 } {
+ return
+ }
+
+ # Timer Group 0 WDT
+ mww 0x6001f064 0x50D83AA1
+ mww 0x6001F048 0
+ # RTC WDT
+ mww 0x6000809C 0x50D83AA1
+ mww 0x60008084 0
+ # SWD
+ mww 0x600080A4 0x8F1D312A
+ mww 0x600080A0 0x84B00000
+}
+
+proc riscv_soc_reset { } {
+ global _RISCV_DMCONTROL
+
+ # This procedure does "digital system reset", i.e. resets
+ # all the peripherals except for the RTC block.
+ # It is called from reset-assert-post target event callback,
+ # after assert_reset procedure was called.
+ # Since we need the hart to to execute a write to RTC_CNTL_SW_SYS_RST,
+ # temporarily take it out of reset. Save the dmcontrol state before
+ # doing so.
+ riscv dmi_write $_RISCV_DMCONTROL 0x80000001
+ # Trigger the reset
+ mww 0x60008000 0x9c00a000
+ # Workaround for stuck in cpu start during calibration.
+ # By writing zero to TIMG_RTCCALICFG_REG, we are disabling calibration
+ mww 0x6001F068 0
+ # Wait for the reset to happen
+ sleep 10
+ poll
+ # Disable the watchdogs again
+ riscv_wdt_disable
+
+ # Here debugger reads allresumeack and allhalted bits as set (0x330a2)
+ # We will clean allhalted state by resuming the core.
+ riscv dmi_write $_RISCV_DMCONTROL 0x40000001
+
+ # Put the hart back into reset state. Note that we need to keep haltreq set.
+ riscv dmi_write $_RISCV_DMCONTROL 0x80000003
+}
+
+proc riscv_memprot_is_enabled { } {
+ global _RISCV_ABS_CMD _RISCV_ABS_DATA0
+
+ # PMPADDR 0-1 covers entire valid IRAM range and PMPADDR 2-3 covers entire DRAM \
region + # pmpcfg0 holds the configuration for the PMP 0-3 address registers
+
+ # read pmpcfg0 and extract into 8-bit variables.
+ riscv dmi_write $_RISCV_ABS_CMD 0x2203a0
+ set pmpcfg0 [riscv dmi_read $_RISCV_ABS_DATA0]
+
+ set pmp0cfg [expr {($pmpcfg0 >> (8 * 0)) & 0xFF}]
+ set pmp1cfg [expr {($pmpcfg0 >> (8 * 1)) & 0xFF}]
+ set pmp2cfg [expr {($pmpcfg0 >> (8 * 2)) & 0xFF}]
+ set pmp3cfg [expr {($pmpcfg0 >> (8 * 3)) & 0xFF}]
+
+ # read PMPADDR 0-3
+ riscv dmi_write $_RISCV_ABS_CMD 0x2203b0
+ set pmpaddr0 [expr {[riscv dmi_read $_RISCV_ABS_DATA0] << 2}]
+ riscv dmi_write $_RISCV_ABS_CMD 0x2203b1
+ set pmpaddr1 [expr {[riscv dmi_read $_RISCV_ABS_DATA0] << 2}]
+ riscv dmi_write $_RISCV_ABS_CMD 0x2203b2
+ set pmpaddr2 [expr {[riscv dmi_read $_RISCV_ABS_DATA0] << 2}]
+ riscv dmi_write $_RISCV_ABS_CMD 0x2203b3
+ set pmpaddr3 [expr {[riscv dmi_read $_RISCV_ABS_DATA0] << 2}]
+
+ set IRAM_LOW 0x40380000
+ set IRAM_HIGH 0x403C0000
+ set DRAM_LOW 0x3FCA0000
+ set DRAM_HIGH 0x3FCE0000
+ set PMP_RWX 0x07
+ set PMP_RW 0x03
+
+ # The lock bit remains unset during the execution of the 2nd stage bootloader.
+ # Thus we do not perform a lock bit check for IRAM and DRAM regions.
+
+ # Check OpenOCD can write and execute from IRAM.
+ if {$pmpaddr0 >= $IRAM_LOW && $pmpaddr1 <= $IRAM_HIGH} {
+ if {($pmp0cfg & $PMP_RWX) != 0 || ($pmp1cfg & $PMP_RWX) != $PMP_RWX} {
+ return 1
+ }
+ }
+
+ # Check OpenOCD can read/write entire DRAM region.
+ if {$pmpaddr2 >= $DRAM_LOW && $pmpaddr3 <= $DRAM_HIGH} {
+ if {($pmp2cfg & $PMP_RW) != 0 && ($pmp3cfg & $PMP_RW) != $PMP_RW} {
+ return 1
+ }
+ }
+
+ return 0
+}
+
+create_esp_target $_ESP_ARCH
diff --git a/tcl/target/esp32c3.cfg b/tcl/target/esp32c3.cfg
new file mode 100644
index 0000000000..d266ad58cd
--- /dev/null
+++ b/tcl/target/esp32c3.cfg
@@ -0,0 +1,81 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+#
+
+# Source the ESP common configuration file.
+source [find target/esp_common.cfg]
+
+# Target specific global variables
+set _CHIPNAME "riscv"
+set _CPUTAPID 0x00005c25
+set _ESP_ARCH "riscv"
+set _ONLYCPU 1
+set _ESP_SMP_TARGET 0
+set _ESP_SMP_BREAK 0
+set _ESP_EFUSE_MAC_ADDR_REG 0x60008844
+
+# Target specific functions should be implemented for each riscv chips.
+proc riscv_wdt_disable { } {
+ # Halt event can occur during config phase (before "init" is done).
+ # Ignore it since mww commands don't work at that time.
+ if { [string compare [command mode] config] == 0 } {
+ return
+ }
+
+ # Timer Group 0 & 1 WDTs
+ mww 0x6001f064 0x50D83AA1
+ mww 0x6001F048 0
+ mww 0x60020064 0x50D83AA1
+ mww 0x60020048 0
+ # RTC WDT
+ mww 0x600080a8 0x50D83AA1
+ mww 0x60008090 0
+ # SWD
+ mww 0x600080b0 0x8F1D312A
+ mww 0x600080ac 0x84B00000
+}
+
+# This is almost identical with the esp32c2_soc_reset.
+# Will be refactored with the other common settings.
+proc riscv_soc_reset { } {
+ global _RISCV_DMCONTROL
+
+ # This procedure does "digital system reset", i.e. resets
+ # all the peripherals except for the RTC block.
+ # It is called from reset-assert-post target event callback,
+ # after assert_reset procedure was called.
+ # Since we need the hart to to execute a write to RTC_CNTL_SW_SYS_RST,
+ # temporarily take it out of reset. Save the dmcontrol state before
+ # doing so.
+ riscv dmi_write $_RISCV_DMCONTROL 0x80000001
+ # Trigger the reset
+ mww 0x60008000 0x9c00a000
+ # Workaround for stuck in cpu start during calibration.
+ # By writing zero to TIMG_RTCCALICFG_REG, we are disabling calibration
+ mww 0x6001F068 0
+ # Wait for the reset to happen
+ sleep 10
+ poll
+ # Disable the watchdogs again
+ riscv_wdt_disable
+
+ # Here debugger reads allresumeack and allhalted bits as set (0x330a2)
+ # We will clean allhalted state by resuming the core.
+ riscv dmi_write $_RISCV_DMCONTROL 0x40000001
+
+ # Put the hart back into reset state. Note that we need to keep haltreq set.
+ riscv dmi_write $_RISCV_DMCONTROL 0x80000003
+}
+
+proc riscv_memprot_is_enabled { } {
+ # IRAM0 PMS lock, SENSITIVE_CORE_X_IRAM0_PMS_CONSTRAIN_0_REG
+ if { [get_mmr_bit 0x600C10A8 0] != 0 } {
+ return 1
+ }
+ # DRAM0 PMS lock, SENSITIVE_CORE_X_DRAM0_PMS_CONSTRAIN_0_REG
+ if { [get_mmr_bit 0x600C10C0 0] != 0 } {
+ return 1
+ }
+ return 0
+}
+
+create_esp_target $_ESP_ARCH
diff --git a/tcl/target/esp32c6.cfg b/tcl/target/esp32c6.cfg
new file mode 100644
index 0000000000..e1ef10a852
--- /dev/null
+++ b/tcl/target/esp32c6.cfg
@@ -0,0 +1,142 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+#
+
+# Source the ESP common configuration file.
+source [find target/esp_common.cfg]
+
+# Target specific global variables
+set _CHIPNAME "riscv"
+set _CPUTAPID 0x0000dc25
+set _ESP_ARCH "riscv"
+set _ONLYCPU 1
+set _ESP_SMP_TARGET 0
+set _ESP_SMP_BREAK 0
+set _ESP_EFUSE_MAC_ADDR_REG 0x600B0844
+
+# Target specific functions should be implemented for each riscv chips.
+proc riscv_wdt_disable { } {
+ # Halt event can occur during config phase (before "init" is done).
+ # Ignore it since mww commands don't work at that time.
+ if { [string compare [command mode] config] == 0 } {
+ return
+ }
+
+ # Timer Group 0 & 1 WDTs
+ mww 0x60008064 0x50D83AA1
+ mww 0x60008048 0
+ mww 0x60009064 0x50D83AA1
+ mww 0x60009048 0
+ # LP_WDT_RTC
+ mww 0x600b1c18 0x50D83AA1
+ mww 0x600B1C00 0
+ # LP_WDT_SWD
+ mww 0x600b1c20 0x50D83AA1
+ mww 0x600b1c1c 0x40000000
+}
+
+proc riscv_soc_reset { } {
+ global _RISCV_DMCONTROL _RISCV_SB_CS _RISCV_SB_ADDR0 _RISCV_SB_DATA0
+
+ riscv dmi_write $_RISCV_DMCONTROL 0x80000001
+ riscv dmi_write $_RISCV_SB_CS 0x48000
+ riscv dmi_write $_RISCV_SB_ADDR0 0x600b1034
+ riscv dmi_write $_RISCV_SB_DATA0 0x80000000
+ # clear dmactive to clear sbbusy otherwise debug module gets stuck
+ riscv dmi_write $_RISCV_DMCONTROL 0
+
+ riscv dmi_write $_RISCV_SB_CS 0x48000
+ riscv dmi_write $_RISCV_SB_ADDR0 0x600b1038
+ riscv dmi_write $_RISCV_SB_DATA0 0x10000000
+
+ # clear dmactive to clear sbbusy otherwise debug module gets stuck
+ riscv dmi_write $_RISCV_DMCONTROL 0
+ riscv dmi_write $_RISCV_DMCONTROL 0x40000001
+ # Here debugger reads dmstatus as 0xc03a2
+
+ # Wait for the reset to happen
+ sleep 10
+ poll
+ # Here debugger reads dmstatus as 0x3a2
+
+ # Disable the watchdogs again
+ riscv_wdt_disable
+
+ # Here debugger reads anyhalted and allhalted bits as set (0x3a2)
+ # We will clean allhalted state by resuming the core.
+ riscv dmi_write $_RISCV_DMCONTROL 0x40000001
+
+ # Put the hart back into reset state. Note that we need to keep haltreq set.
+ riscv dmi_write $_RISCV_DMCONTROL 0x80000003
+}
+
+proc riscv_memprot_is_enabled { } {
+ global _RISCV_ABS_CMD _RISCV_ABS_DATA0
+
+ # If IRAM/DRAM split is enabled TOR address match mode is used.
+ # If IRAM/DRAM split is disabled NAPOT mode is used.
+ # In order to determine if the IRAM/DRAM regions are protected against RWX/RW,
+ # it is necessary to first read the mode and then apply the appropriate method for \
checking. + # We can understand the mode reading pmp5cfg in pmpcfg1 register.
+ # If it is none we know that pmp6cfg and pmp7cfg is in TOR mode.
+
+ # Read pmpcfg1 and extract into 8-bit variables.
+ riscv dmi_write $_RISCV_ABS_CMD 0x2203a1
+ set pmpcfg1 [riscv dmi_read $_RISCV_ABS_DATA0]
+
+ set pmp5cfg [expr {($pmpcfg1 >> (8 * 1)) & 0xFF}]
+ set pmp6cfg [expr {($pmpcfg1 >> (8 * 2)) & 0xFF}]
+ set pmp7cfg [expr {($pmpcfg1 >> (8 * 3)) & 0xFF}]
+
+ set IRAM_LOW 0x40800000
+ set IRAM_HIGH 0x40880000
+ set DRAM_LOW 0x40800000
+ set DRAM_HIGH 0x40880000
+ set PMP_RWX 0x07
+ set PMP_RW 0x03
+ set PMP_A [expr {($pmp5cfg >> 3) & 0x03}]
+
+ if {$PMP_A == 0} {
+ # TOR mode used to protect valid address space.
+
+ # Read PMPADDR 5-7
+ riscv dmi_write $_RISCV_ABS_CMD 0x2203b5
+ set pmpaddr5 [expr {[riscv dmi_read $_RISCV_ABS_DATA0] << 2}]
+ riscv dmi_write $_RISCV_ABS_CMD 0x2203b6
+ set pmpaddr6 [expr {[riscv dmi_read $_RISCV_ABS_DATA0] << 2}]
+ riscv dmi_write $_RISCV_ABS_CMD 0x2203b7
+ set pmpaddr7 [expr {[riscv dmi_read $_RISCV_ABS_DATA0] << 2}]
+
+ # The lock bit remains unset during the execution of the 2nd stage bootloader.
+ # Thus we do not perform a lock bit check for IRAM and DRAM regions.
+
+ # Check OpenOCD can write and execute from IRAM.
+ if {$pmpaddr5 >= $IRAM_LOW && $pmpaddr6 <= $IRAM_HIGH} {
+ if {($pmp5cfg & $PMP_RWX) != 0 || ($pmp6cfg & $PMP_RWX) != $PMP_RWX} {
+ return 1
+ }
+ }
+
+ # Check OpenOCD can read/write entire DRAM region.
+ if {$pmpaddr7 >= $DRAM_LOW && $pmpaddr7 <= $DRAM_HIGH} {
+ if {($pmp7cfg & $PMP_RW) != $PMP_RW} {
+ return 1
+ }
+ }
+ } elseif {$PMP_A == 3} {
+ # NAPOT mode used to protect valid address space.
+
+ # Read PMPADDR 5
+ riscv dmi_write $_RISCV_ABS_CMD 0x2203b5
+ set pmpaddr5 [expr {[riscv dmi_read $_RISCV_ABS_DATA0]}]
+
+ # Expected value written to the pmpaddr5
+ set pmpaddr_napot [expr {($IRAM_LOW | (($IRAM_HIGH - $IRAM_LOW - 1) >> 1)) >> 2}]
+ if {($pmpaddr_napot != $pmpaddr5) || ($pmp5cfg & $PMP_RWX) != $PMP_RWX} {
+ return 1
+ }
+ }
+
+ return 0
+}
+
+create_esp_target $_ESP_ARCH
diff --git a/tcl/target/esp32h2.cfg b/tcl/target/esp32h2.cfg
new file mode 100644
index 0000000000..45f598f731
--- /dev/null
+++ b/tcl/target/esp32h2.cfg
@@ -0,0 +1,122 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+#
+
+# Source the ESP common configuration file.
+source [find target/esp_common.cfg]
+
+# Target specific global variables
+set _CHIPNAME "riscv"
+set _CPUTAPID 0x00010c25
+set _ESP_ARCH "riscv"
+set _ONLYCPU 1
+set _ESP_SMP_TARGET 0
+set _ESP_SMP_BREAK 0
+set _ESP_EFUSE_MAC_ADDR_REG 0x600B0844
+
+# Target specific functions should be implemented for each riscv chips.
+proc riscv_wdt_disable { } {
+ # Halt event can occur during config phase (before "init" is done).
+ # Ignore it since mww commands don't work at that time.
+ if { [string compare [command mode] config] == 0 } {
+ return
+ }
+
+ # Timer Group 0 & 1 WDTs
+ mww 0x60009064 0x50D83AA1
+ mww 0x60009048 0
+ mww 0x6000A064 0x50D83AA1
+ mww 0x6000A048 0
+ # WDT_RTC
+ #mww 0x600b1c18 0x50D83AA1
+ #mww 0x600B1C00 0
+ # WDT_SWD
+ #mww 0x600b1c20 0x8F1D312A
+ #mww 0x600b1c1c 0x84B00000
+}
+
+proc riscv_soc_reset { } {
+ global _RISCV_DMCONTROL _RISCV_SB_CS _RISCV_SB_ADDR0 _RISCV_SB_DATA0
+
+ riscv dmi_write $_RISCV_DMCONTROL 0x80000001
+ riscv dmi_write $_RISCV_SB_CS 0x48000
+ riscv dmi_write $_RISCV_SB_ADDR0 0x600b1034
+ riscv dmi_write $_RISCV_SB_DATA0 0x80000000
+ # clear dmactive to clear sbbusy otherwise debug module gets stuck
+ riscv dmi_write $_RISCV_DMCONTROL 0
+
+ riscv dmi_write $_RISCV_SB_CS 0x48000
+ riscv dmi_write $_RISCV_SB_ADDR0 0x600b1038
+ riscv dmi_write $_RISCV_SB_DATA0 0x10000000
+
+ # clear dmactive to clear sbbusy otherwise debug module gets stuck
+ riscv dmi_write $_RISCV_DMCONTROL 0
+ riscv dmi_write $_RISCV_DMCONTROL 0x40000001
+ # Here debugger reads dmstatus as 0xc03a2
+
+ # Wait for the reset to happen
+ sleep 10
+ poll
+ # Here debugger reads dmstatus as 0x3a2
+
+ # Disable the watchdogs again
+ riscv_wdt_disable
+
+ # Here debugger reads anyhalted and allhalted bits as set (0x3a2)
+ # We will clean allhalted state by resuming the core.
+ riscv dmi_write $_RISCV_DMCONTROL 0x40000001
+
+ # Put the hart back into reset state. Note that we need to keep haltreq set.
+ riscv dmi_write $_RISCV_DMCONTROL 0x80000003
+}
+
+proc riscv_memprot_is_enabled { } {
+ global _RISCV_ABS_CMD _RISCV_ABS_DATA0
+ # If IRAM/DRAM split is enabled, PMPADDR 5-6 will cover valid IRAM region and \
PMPADDR 7 will cover valid DRAM region + # Only TOR mode is used for IRAM and DRAM \
protections. +
+ # Read pmpcfg1 and extract into 8-bit variables.
+ riscv dmi_write $_RISCV_ABS_CMD 0x2203a1
+ set pmpcfg1 [riscv dmi_read $_RISCV_ABS_DATA0]
+
+ set pmp5cfg [expr {($pmpcfg1 >> (8 * 1)) & 0xFF}]
+ set pmp6cfg [expr {($pmpcfg1 >> (8 * 2)) & 0xFF}]
+ set pmp7cfg [expr {($pmpcfg1 >> (8 * 3)) & 0xFF}]
+
+ # Read PMPADDR 5-7
+ riscv dmi_write $_RISCV_ABS_CMD 0x2203b5
+ set pmpaddr5 [expr {[riscv dmi_read $_RISCV_ABS_DATA0] << 2}]
+ riscv dmi_write $_RISCV_ABS_CMD 0x2203b6
+ set pmpaddr6 [expr {[riscv dmi_read $_RISCV_ABS_DATA0] << 2}]
+ riscv dmi_write $_RISCV_ABS_CMD 0x2203b7
+ set pmpaddr7 [expr {[riscv dmi_read $_RISCV_ABS_DATA0] << 2}]
+
+ set IRAM_LOW 0x40800000
+ set IRAM_HIGH 0x40850000
+ set DRAM_LOW 0x40800000
+ set DRAM_HIGH 0x40850000
+
+ set PMP_RWX 0x07
+ set PMP_RW 0x03
+
+ # The lock bit remains unset during the execution of the 2nd stage bootloader.
+ # Thus, we do not perform a lock bit check for IRAM and DRAM regions.
+
+ # Check OpenOCD can write and execute from IRAM.
+ if {$pmpaddr5 >= $IRAM_LOW && $pmpaddr6 <= $IRAM_HIGH} {
+ if {($pmp5cfg & $PMP_RWX) != 0 || ($pmp6cfg & $PMP_RWX) != $PMP_RWX} {
+ return 1
+ }
+ }
+
+ # Check OpenOCD can read/write entire DRAM region.
+ # If IRAM/DRAM split is disabled, pmpaddr7 will be zero, checking only IRAM region \
is enough. + if {$pmpaddr7 != 0 && $pmpaddr7 >= $DRAM_LOW && $pmpaddr7 <= $DRAM_HIGH} \
{ + if {($pmp7cfg & $PMP_RW) != $PMP_RW} {
+ return 1
+ }
+ }
+
+ return 0
+}
+
+create_esp_target $_ESP_ARCH
diff --git a/tcl/target/esp_common.cfg b/tcl/target/esp_common.cfg
index ac8cd6a198..af2f6ad2ca 100644
--- a/tcl/target/esp_common.cfg
+++ b/tcl/target/esp_common.cfg
@@ -6,6 +6,14 @@ source [find bitsbytes.tcl]
source [find memory.tcl]
source [find mmr_helpers.tcl]
+# Riscv Debug Module Registers which are used around esp configuration files.
+set _RISCV_ABS_DATA0 0x04
+set _RISCV_DMCONTROL 0x10
+set _RISCV_ABS_CMD 0x17
+set _RISCV_SB_CS 0x38
+set _RISCV_SB_ADDR0 0x39
+set _RISCV_SB_DATA0 0x3C
+
# Common ESP chips definitions
# Espressif supports only NuttX in the upstream.
@@ -69,13 +77,12 @@ proc create_esp_target { ARCH } {
set_esp_common_variables
create_esp_jtag
create_openocd_targets
- configure_openocd_events
+ configure_openocd_events $ARCH
if { $ARCH == "xtensa"} {
configure_esp_xtensa_default_settings
} else {
- # riscv targets are not upstreamed yet.
- # they can be found at the official Espressif fork.
+ configure_esp_riscv_default_settings
}
}
@@ -131,7 +138,6 @@ proc configure_event_halted { } {
$_TARGETNAME_0 configure -event halted {
global _ESP_WDT_DISABLE
$_ESP_WDT_DISABLE
- esp halted_event_handler
}
}
@@ -167,12 +173,25 @@ proc configure_event_gdb_attach { } {
}
}
-proc configure_openocd_events { } {
+proc configure_openocd_events { ARCH } {
+ if { $ARCH == "riscv" } {
+ configure_event_halted
+ }
configure_event_examine_end
configure_event_reset_assert_post
configure_event_gdb_attach
}
+proc configure_esp_riscv_default_settings { } {
+ gdb_breakpoint_override hard
+ riscv set_reset_timeout_sec 2
+ riscv set_command_timeout_sec 5
+ riscv set_mem_access sysbus progbuf abstract
+ riscv set_ebreakm on
+ riscv set_ebreaks on
+ riscv set_ebreaku on
+}
+
proc configure_esp_xtensa_default_settings { } {
global _TARGETNAME_0 _ESP_SMP_BREAK _FLASH_VOLTAGE _CHIPNAME
--
[prev in list] [next in list] [prev in thread] [next in thread]
Configure |
About |
News |
Add a list |
Sponsored by KoreLogic