[prev in list] [next in list] [prev in thread] [next in thread]
List: openbsd-arm
Subject: Re: BeagleBone Black sd? confusion
From: Jan Stary <hans () stare ! cz>
Date: 2019-06-07 11:47:34
Message-ID: 20190607114734.GA71512 () www ! stare ! cz
[Download RAW message or body]
On Jun 07 11:44:01, hans@stare.cz wrote:
> Hi all,
>
> this is current/armv7 on a BeagleBone Black, dmesg below.
> It has an internal flash storage (2GB), and I put a 32GB SD into it,
> which is where the OpenBSD installation lives.
>
> The boot seems to be changing its mind about what sd0 and sd1 is.
> After a reboot, I see the same dmesg, except:
>
> --- dmesg/beaglebone-black.20190606 Thu Jun 6 13:54:13 2019
> +++ /tmp/dmesg Fri Jun 7 11:24:21 2019
> @@ -1,7 +1,7 @@
> OpenBSD 6.5-current (GENERIC) #0: Thu Jun 6 12:46:47 CEST 2019
> hans@bbb.stare.cz:/usr/src/sys/arch/armv7/compile/GENERIC
> real mem = 477818880 (455MB)
> -avail mem = 458125312 (436MB)
> +avail mem = 458117120 (436MB)
> mainbus0 at root: TI AM335x BeagleBone Black
> cpu0 at mainbus0: ARM Cortex-A8 r3p2 (ARMv7)
> cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
> @@ -78,17 +78,17 @@ amdisplay0: no display attached.
> "aes" at simplebus0 not configured
> "mcasp" at simplebus0 not configured
> "rng" at simplebus0 not configured
> -scsibus0 at sdmmc1: 2 targets, initiator 0
> -sd0 at scsibus0 targ 1 lun 0: <SD/MMC, MMC02G, 0000> SCSI2 0/direct removable
> -sd0: 1832MB, 512 bytes/sector, 3751936 sectors
> -scsibus1 at sdmmc0: 2 targets, initiator 0
> -sd1 at scsibus1 targ 1 lun 0: <SD/MMC, SU32G, 0080> SCSI2 0/direct removable
> -sd1: 30436MB, 512 bytes/sector, 62333952 sectors
> +scsibus0 at sdmmc0: 2 targets, initiator 0
> +sd0 at scsibus0 targ 1 lun 0: <SD/MMC, SU32G, 0080> SCSI2 0/direct removable
> +sd0: 30436MB, 512 bytes/sector, 62333952 sectors
> +scsibus1 at sdmmc1: 2 targets, initiator 0
> +sd1 at scsibus1 targ 1 lun 0: <SD/MMC, MMC02G, 0000> SCSI2 0/direct removable
> +sd1: 1832MB, 512 bytes/sector, 3751936 sectors
> vscsi0 at root
> scsibus2 at vscsi0: 256 targets
> softraid0 at root
> scsibus3 at softraid0: 256 targets
> bootfile: sd0a:/bsd
> boot device: sd0
> -root on sd1a (93aae518915c8841.a) swap on sd1b dump on sd1b
> +root on sd0a (93aae518915c8841.a) swap on sd0b dump on sd0b
> WARNING: CHECK AND RESET THE DATE!
>
> Why is it changing?
>
> On this occasion, it seems right: it boots sd0a:/bsd,
> sd0 being the boot device, and
>
> /dev/sd0a 252M 55.1M 185M 23% /
> /dev/sd0d 1.4G 1.1G 231M 83% /usr
> /dev/sd0e 2.9G 327M 2.5G 11% /usr/local
> /dev/sd0f 508M 9.0M 473M 2% /var
> /dev/sd0g 246M 11.4M 222M 5% /var/log
> /dev/sd0h 2.0G 1.1M 1.9G 0% /var/www
> /dev/sd0j 61.6M 2.0K 58.5M 0% /var/mail
> /dev/sd0k 2.0G 16.0K 1.9G 0% /tmp
> /dev/sd0l 5.7G 407M 5.0G 7% /home
> /dev/sd0m 6.6G 1.2G 5.0G 19% /backup
>
> so it is the 32GB SD card (the internal flash isn't this large).
> But in the dmesg below, it's
>
> bootfile: sd0a:/bsd
> boot device: sd0
> root on sd1a (93aae518915c8841.a) swap on sd1b dump on sd1b
Just to be clear: it runs fine;
it just thinks that the 32GB card is sd1.
Jan
> Copyright (c) 1982, 1986, 1989, 1991, 1993
> The Regents of the University of California. All rights reserved.
> Copyright (c) 1995-2019 OpenBSD. All rights reserved. https://www.OpenBSD.org
>
> OpenBSD 6.5-current (GENERIC) #0: Thu Jun 6 12:46:47 CEST 2019
> hans@bbb.stare.cz:/usr/src/sys/arch/armv7/compile/GENERIC
> real mem = 477818880 (455MB)
> avail mem = 458125312 (436MB)
> mainbus0 at root: TI AM335x BeagleBone Black
> cpu0 at mainbus0: ARM Cortex-A8 r3p2 (ARMv7)
> cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
> cpu0: 32KB(64b/l,4way) I-cache, 32KB(64b/l,4way) wr-back D-cache
> omap0 at mainbus0
> prcm0 at omap0 rev 0.2
> dmtimer0 at omap0 rev 3.1
> dmtimer1 at omap0 rev 3.1
> simplebus0 at mainbus0: "ocp"
> simplebus1 at simplebus0: "l4_wkup"
> "wkup_m3" at simplebus1 not configured
> simplebus2 at simplebus1: "prcm"
> "l4_per_cm" at simplebus2 not configured
> "l4_wkup_cm" at simplebus2 not configured
> "mpu_cm" at simplebus2 not configured
> "l4_rtc_cm" at simplebus2 not configured
> "gfx_l3_cm" at simplebus2 not configured
> "l4_cefuse_cm" at simplebus2 not configured
> simplebus3 at simplebus1: "scm"
> syscon0 at simplebus3: "scm_conf"
> pinctrl0 at simplebus3
> "wkup_m3_ipc" at simplebus3 not configured
> "dma-router" at simplebus3 not configured
> intc0 at simplebus0 rev 5.0
> "edma" at simplebus0 not configured
> "tptc" at simplebus0 not configured
> "tptc" at simplebus0 not configured
> "tptc" at simplebus0 not configured
> omgpio0 at simplebus0: rev 0.1
> gpio0 at omgpio0: 32 pins
> omgpio1 at simplebus0: rev 0.1
> gpio1 at omgpio1: 32 pins
> omgpio2 at simplebus0: rev 0.1
> gpio2 at omgpio2: 32 pins
> omgpio3 at simplebus0: rev 0.1
> gpio3 at omgpio3: 32 pins
> com0 at simplebus0: ti16750, 64 byte fifo
> com0: console
> tiiic0 at simplebus0 rev 0.11
> iic0 at tiiic0
> "ti,tps65217" at iic0 addr 0x24 not configured
> "atmel,24c256" at iic0 addr 0x50 not configured
> nxphdmi0 at iic0 addr 0x70: rev 0x0301
> nxphdmi0: no display detected
> tiiic1 at simplebus0 rev 0.11
> iic1 at tiiic1
> "atmel,24c256" at iic1 addr 0x54 not configured
> "atmel,24c256" at iic1 addr 0x55 not configured
> "atmel,24c256" at iic1 addr 0x56 not configured
> "atmel,24c256" at iic1 addr 0x57 not configured
> ommmc0 at simplebus0
> sdmmc0 at ommmc0: 4-bit, sd high-speed, mmc high-speed
> ommmc1 at simplebus0
> sdmmc1 at ommmc1: 1-bit
> "spinlock" at simplebus0 not configured
> omdog0 at simplebus0 rev 0.1
> "mailbox" at simplebus0 not configured
> "timer" at simplebus0 not configured
> "timer" at simplebus0 not configured
> "timer" at simplebus0 not configured
> "timer" at simplebus0 not configured
> "timer" at simplebus0 not configured
> "timer" at simplebus0 not configured
> "timer" at simplebus0 not configured
> "rtc" at simplebus0 not configured
> "usb" at simplebus0 not configured
> cpsw0 at simplebus0: version 1.12 (0), address 90:59:af:82:2e:7e
> ukphy0 at cpsw0 phy 0: Generic IEEE 802.3u media interface, rev. 1: OUI 0x0001f0, model 0x000f
> "ocmcram" at simplebus0 not configured
> amdisplay0 at simplebus0
> amdisplay0: no display attached.
> "emif" at simplebus0 not configured
> "sham" at simplebus0 not configured
> "aes" at simplebus0 not configured
> "mcasp" at simplebus0 not configured
> "rng" at simplebus0 not configured
> scsibus0 at sdmmc1: 2 targets, initiator 0
> sd0 at scsibus0 targ 1 lun 0: <SD/MMC, MMC02G, 0000> SCSI2 0/direct removable
> sd0: 1832MB, 512 bytes/sector, 3751936 sectors
> scsibus1 at sdmmc0: 2 targets, initiator 0
> sd1 at scsibus1 targ 1 lun 0: <SD/MMC, SU32G, 0080> SCSI2 0/direct removable
> sd1: 30436MB, 512 bytes/sector, 62333952 sectors
> vscsi0 at root
> scsibus2 at vscsi0: 256 targets
> softraid0 at root
> scsibus3 at softraid0: 256 targets
> bootfile: sd0a:/bsd
> boot device: sd0
> root on sd1a (93aae518915c8841.a) swap on sd1b dump on sd1b
> WARNING: CHECK AND RESET THE DATE!
>
[prev in list] [next in list] [prev in thread] [next in thread]
Configure |
About |
News |
Add a list |
Sponsored by KoreLogic