[prev in list] [next in list] [prev in thread] [next in thread]
List: linux-scsi
Subject: [PATCH 04/11] qla4xxx: Updated firmware ready timeout algorithm
From: Vikas Chaudhary <vikas.chaudhary () qlogic ! com>
Date: 2010-04-28 6:22:37
Message-ID: 20100428061037.GA11125 () sles11sp1b1 ! qlogic ! org
[Download RAW message or body]
Updated firmware ready timeout algorithm to prevent
long delays and use jiffies to time out instead of
counter. Also use msleep_interruptible instead of msleep.
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
---
drivers/scsi/qla4xxx/ql4_init.c | 20 +++++++++++---------
1 files changed, 11 insertions(+), 9 deletions(-)
diff --git a/drivers/scsi/qla4xxx/ql4_init.c b/drivers/scsi/qla4xxx/ql4_init.c
index 7f6cc2e..beaeb18 100644
--- a/drivers/scsi/qla4xxx/ql4_init.c
+++ b/drivers/scsi/qla4xxx/ql4_init.c
@@ -1046,7 +1046,7 @@ static void qla4x00_pci_config(struct scsi_qla_host *ha)
static int qla4xxx_start_firmware_from_flash(struct scsi_qla_host *ha)
{
int status = QLA_ERROR;
- uint32_t max_wait_time;
+ unsigned long max_wait_time;
unsigned long flags;
uint32_t mbox_status;
@@ -1078,7 +1078,10 @@ static int qla4xxx_start_firmware_from_flash(struct scsi_qla_host *ha)
spin_unlock_irqrestore(&ha->hardware_lock, flags);
/* Wait for firmware to come UP. */
- max_wait_time = FIRMWARE_UP_TOV * 4;
+ DEBUG2(printk(KERN_INFO "scsi%ld: %s: Wait up to %d seconds for "
+ "boot firmware to complete...\n",
+ ha->host_no, __func__, FIRMWARE_UP_TOV));
+ max_wait_time = jiffies + (FIRMWARE_UP_TOV * HZ);
do {
uint32_t ctrl_status;
@@ -1092,16 +1095,15 @@ static int qla4xxx_start_firmware_from_flash(struct scsi_qla_host *ha)
if (mbox_status == MBOX_STS_COMMAND_COMPLETE)
break;
- DEBUG2(printk("scsi%ld: %s: Waiting for boot firmware to "
- "complete... ctrl_sts=0x%x, remaining=%d\n",
- ha->host_no, __func__, ctrl_status,
- max_wait_time));
+ DEBUG2(printk(KERN_INFO "scsi%ld: %s: Waiting for boot "
+ "firmware to complete... ctrl_sts=0x%x\n",
+ ha->host_no, __func__, ctrl_status));
- msleep(250);
- } while ((max_wait_time--));
+ msleep_interruptible(250);
+ } while (!time_after_eq(jiffies, max_wait_time));
if (mbox_status == MBOX_STS_COMMAND_COMPLETE) {
- DEBUG(printk("scsi%ld: %s: Firmware has started\n",
+ DEBUG(printk(KERN_INFO "scsi%ld: %s: Firmware has started\n",
ha->host_no, __func__));
spin_lock_irqsave(&ha->hardware_lock, flags);
--
1.7.0.5
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
[prev in list] [next in list] [prev in thread] [next in thread]
Configure |
About |
News |
Add a list |
Sponsored by KoreLogic