[prev in list] [next in list] [prev in thread] [next in thread]
List: suse-amd64
Subject: Re: [suse-amd64] lm_sensors modules on SuSE-9.0
From: "Mikhail Kuzminsky" <kus () free ! net>
Date: 2004-07-28 19:05:00
Message-ID: web-69824 () free ! net
[Download RAW message or body]
In message from Darrell Shively <sused@mucus.com> (Tue, 27 Jul 2004
23:24:21 -0700):
>
>Unless I'm missing something, these are all the sensor related
>modules that get loaded in my system:
> w83781d
> eeprom
> lm85
> i2c-proc
> i2c-isa
> i2c-amd756
> i2c-amd8111
> i2c-core
>
You are absolutely right in both (this and previous) messages !
1) amd756 module from SuSE binary RPM I used is wrong for S2880, and
can't be insmod'ed successfully (init_module says "No such
device").
2) The board has W83627hf chip, but I may use w83781d driver (I
thought about w83627hf driver, which is absent in RPM, but this driver
is necessary only for ISA access to W83627hf Super I/O)
3) I run sensors -s and then sensors w/o amd756 module loaded
(I don't know, which chips placed on the board - W83627hf or adm1027
on amd756 bus - are responsible just for temperature). The temperature
I see (76C) looks as wrong; at BIOS level I see 45C. The reason may be
also incorrect /etc/sensors.conf (I use configuration file from SuSE
RPM, not from Tyan web-site, see ticket#1713 for lm_sensors):
w83627hf-isa-0290
Adapter: ISA adapter
Algorithm: ISA algorithm
VCore 1: +1.52 V (min = +1.93 V, max = +2.14 V)
VCore 2: +1.55 V (min = +1.93 V, max = +2.14 V)
+3.3V: +3.37 V (min = +3.13 V, max = +3.45 V)
+5V: +5.02 V (min = +4.72 V, max = +5.24 V)
+12V: +4.67 V (min = +10.79 V, max = +13.19 V)
-12V: -2.27 V (min = -13.21 V, max = -10.90 V)
-5V: -3.91 V (min = -5.26 V, max = -4.76 V)
V5SB: +5.44 V (min = +4.72 V, max = +5.24 V)
VBat: +3.26 V (min = +2.40 V, max = +3.60 V)
fan1: 3169 RPM (min = 3000 RPM, div = 2)
fan2: 3276 RPM (min = 3000 RPM, div = 2)
fan3: 0 RPM (min = 3000 RPM, div = 2)
temp1: +76°C (limit = +60°C) sensor =
thermistor ALARM
temp2: +76.0°C (limit = +60°C, hysteresis = +50°C) sensor =
thermistor ALARM
temp3: +76.0°C (limit = +60°C, hysteresis = +50°C) sensor =
thermistor ALARM
vid: +2.050 V
alarms: Chassis intrusion detection ALARM
beep_enable:
Sound alarm disabled
4) The only question remains now is - should I re-compile
i2c/lm_sensors
modules in the case of upgrade form kernel 2.4.21-149 to 2.4.21-215
for example ?
Thanks for help !!
Yours
Mikhail
>This was determined by diff'ing the output of lsmod with and without
>sensord running. I don't know if it is of interest, but here is the
> output of the sensors command on this system:
>
>$ sensors
>adt7463-i2c-1-2e
>Adapter: SMBus AMD75x adapter at 50e0
>Algorithm: Non-I2C SMBus adapter
>CPU0 DDR 2.5:
> +2.516 V (min = +2.37 V, max = +2.63 V)
>CPU0 DDR VTT:
> +1.260 V (min = +1.18 V, max = +1.31 V)
>3.3VSB: +3.339 V (min = +3.13 V, max = +3.47 V)
>+5V: +5.111 V (min = +4.74 V, max = +5.26 V)
>+12V: +12.063 V (min = +11.38 V, max = +12.62 V)
>FAN3 (REAR):
> 2236 RPM (min = 3000 RPM) ALARM
>FAN4 (BOTTOM):
> 0 RPM (min = 3000 RPM) ALARM
>FAN1 (CPU0):
> 5538 RPM (min = 3000 RPM)
>FAN2 (CPU1):
> 6040 RPM (min = 3000 RPM)
>CPU1 Temp:+44.50°C (min = -128°C, max = +127°C)
>System Temp:
> +41.75°C (min = -127°C, max = +127°C)
>CPU0 Temp:+50.25°C (min = -127°C, max = +127°C)
>pwm1 fan: 255
>pwm2 fan: 255
>pwm3 fan: 255
>vid: +1.800 V (VRM Version 9.1)
>
>eeprom-i2c-1-50
>Adapter: SMBus AMD75x adapter at 50e0
>Algorithm: Non-I2C SMBus adapter
>Memory type: DDR SDRAM DIMM SPD
>Memory size (MB): 512
>
>eeprom-i2c-1-51
>Adapter: SMBus AMD75x adapter at 50e0
>Algorithm: Non-I2C SMBus adapter
>
>eeprom-i2c-1-54
>Adapter: SMBus AMD75x adapter at 50e0
>Algorithm: Non-I2C SMBus adapter
>
>eeprom-i2c-1-55
>Adapter: SMBus AMD75x adapter at 50e0
>Algorithm: Non-I2C SMBus adapter
>
>w83627hf-isa-0290
>Adapter: ISA adapter
>Algorithm: ISA algorithm
>CPU0 Vcore:
> +1.50 V (min = +1.42 V, max = +1.56 V)
>CPU1 Vcore:
> +1.52 V (min = +1.42 V, max = +1.56 V)
>+3.3V: +3.32 V (min = +3.13 V, max = +3.45 V)
>CPU1 DDR VTT:
> +1.23 V (min = +1.18 V, max = +1.31 V)
>CPU1 DDR 2.5:
> +2.51 V (min = +2.36 V, max = +2.62 V)
>VDD_CPU0: +1.20 V (min = +1.13 V, max = +1.26 V)
>VBat: +3.26 V (min = +3.13 V, max = +3.45 V)
>FAN5 (TOP):
> 0 RPM (min = 3000 RPM, div = 2)
>FAN6 (FRONT):
> 0 RPM (min = 3000 RPM, div = 2)
>rear temp: +46°C (limit = +40°C, hysteresis = +37°C) sensor =
>thermistor
>I/O panel temp:
> +41.0°C (limit = +52°C, hysteresis = +47°C) sensor =
>thermistor
>vid: +1.950 V
>alarms:
>beep_enable:
> Sound alarm disabled
>
--
Check the List-Unsubscribe header to unsubscribe
For additional commands, email: suse-amd64-help@suse.com
[prev in list] [next in list] [prev in thread] [next in thread]
Configure |
About |
News |
Add a list |
Sponsored by KoreLogic