[prev in list] [next in list] [prev in thread] [next in thread]
List: strongswan-users
Subject: [strongSwan] Help needed to use stongswan with amazon VPC
From: Jean-Sébastien_Frerot
Date: 2011-07-08 17:24:58
Message-ID: 4E173D6A.9090603 () gameloft ! com
[Download RAW message or body]
[Attachment #2 (multipart/signed)]
[Attachment #4 (multipart/alternative)]
Hi, I'm trying to connect to amazon VPN using strongswan 4.2.4 on debian
5.0.8 but I have some problems.
Here is how the setup is designed from amazon side.
Amazon have 2 public IP addresses and we connect to the 2 ips using 2
distinct vpn connection. However those connection are initiated (on our
side) by only 1 server. So we use the same public ip address on our side.
So we establish the connection with the following subnets
169.254.255.0/30 and 169.254.255.4/30 (one for each vpn connection).
So far, I'm able to make this connection up and running. The problem
comes when I need to route other subnets to this VPN connection with
BGP. In my case I defined on amazon side the following subnet:
10.144.0.0/16. But when I try to use this subnet the packets don't seem
to be routed to the tunnel. Of course bgp is up and the routes are added
by bgp.
I've been able to make the setup work with manual commands and weird (to
me since i'm far from beeing an expert on ipsec/ike) configuration. But
i'm pretty sure there is a clean way to make this works without too much
problems.
Could you please help me on how to setup this connection properly?
Thank you.
Here are the 2 configuration settings I've been able to use to bring up
the vpn connection. The 1st one can't route the 10.144/16 network even
though I add xfrm policies, and the 2nd one is working, but only one vpn
comes up because it can't add the same route on the 2 vpn connections
and I have to run some ip xfrm commands to make it work.
Here is the amazon VPN Connection Configuration
*connection 1:*
Outside IP Addresses:
- Customer Gateway: : *my_pub_ip*
- VPN Gateway : 72.21.209.225
Inside IP Addresses
- Customer Gateway : 169.254.255.2/30
- VPN Gateway : 169.254.255.1/30
Configure the IKE SA as follows
- Authentication Method : Pre-Shared Key
- Pre-Shared Key : *my_psk1*
- Authentication Algorithm : sha1
- Encryption Algorithm : aes-128-cbc
- Lifetime : 28800 seconds
- Phase 1 Negotiation Mode : main
- Perfect Forward Secrecy : Diffie-Hellman Group 2
Configure the IPSec SA as follows:
- Protocol : esp
- Authentication Algorithm : hmac-sha1-96
- Encryption Algorithm : aes-128-cbc
- Lifetime : 3600 seconds
- Mode : tunnel
- Perfect Forward Secrecy : Diffie-Hellman Group 2
The Border Gateway Protocol (BGPv4) is used within the tunnel, between
the inside
IP addresses, to exchange routes from the VPC to your home network. Each
BGP router has an Autonomous System Number (ASN). Your ASN was provided
to AWS when the Customer Gateway was created.
BGP Configuration Options:
- Customer Gateway ASN : 65136
- VPN Gateway ASN : 7224
- Neighbor IP Address : 169.254.255.1
- Neighbor Hold Time : 30
Configure BGP to announce the default route (0.0.0.0/0) to the VPN
Connection
Gateway. The VPN Gateway will announce prefixes to your Customer
Gateway based upon the prefixes assigned in the creation of the VPC.
*Connection 2:*
Outside IP Addresses:
- Customer Gateway: : *my_pub_ip*
- VPN Gateway : 72.21.209.193
Inside IP Addresses
- Customer Gateway : 169.254.255.6/30
- VPN Gateway : 169.254.255.5/30
Configure the IKE SA as follows
- Authentication Method : Pre-Shared Key
- Pre-Shared Key : *my_psk2*
- Authentication Algorithm : sha1
- Encryption Algorithm : aes-128-cbc
- Lifetime : 28800 seconds
- Phase 1 Negotiation Mode : main
- Perfect Forward Secrecy : Diffie-Hellman Group 2
Configure the IPSec SA as follows:
- Protocol : esp
- Authentication Algorithm : hmac-sha1-96
- Encryption Algorithm : aes-128-cbc
- Lifetime : 3600 seconds
- Mode : tunnel
- Perfect Forward Secrecy : Diffie-Hellman Group 2
The Border Gateway Protocol (BGPv4) is used within the tunnel, between
the inside
IP addresses, to exchange routes from the VPC to your home network. Each
BGP router has an Autonomous System Number (ASN). Your ASN was provided
to AWS when the Customer Gateway was created.
BGP Configuration Options:
- Customer Gateway ASN : 65136
- VPN Gateway ASN : 7224
- Neighbor IP Address : 169.254.255.5
- Neighbor Hold Time : 30
Configure BGP to announce the default route (0.0.0.0/0) to the VPN
Connection
Gateway. The VPN Gateway will announce prefixes to your Customer
Gateway based upon the prefixes assigned in the creation of the VPC.
And here is the configuration I've been trying to setup.
*configuration 1: (10.144/16 not working at all)*
ipsec.secrets:
*my_pub_ip* 72.21.209.225 : PSK "*my_psk1*"
*my_pub_ip* 72.21.209.193 : PSK "*my_psk2*"
strongswan.conf:
charon {
}
pluto {
}
libstrongswan {
}
ipsec.conf
config setup
charonstart=no
plutostart=yes
strictcrlpolicy=no
conn vac1
keyexchange=ikev1
auto=start
authby=psk
compress=no
type=tunnel
ike=aes128-sha1-modp1024
pfs=yes
left=*my_pub_ip*
leftsourceip=169.254.255.2/30
right=72.21.209.225
rightsourceip=169.254.255.1/30
conn vac2
keyexchange=ikev1
auto=start
authby=psk
compress=no
type=tunnel
ike=aes128-sha1-modp1024
pfs=yes
left=*my_pub_ip*
leftsourceip=169.254.255.6/30
right=72.21.209.193
rightsourceip=169.254.255.5/30
sudo /etc/init.d/ipsec start
Starting strongSwan 4.2.4 IPsec [starter]...
multiple default routes - cannot cope with %defaultroute!!!
ip xfrm state
src *my_pub_ip* dst 72.21.209.225
proto esp spi 0xd49408d7 reqid 16385 mode tunnel
replay-window 32
auth hmac(sha1) 0x3696cf0b7cbd526edf0b8793084334a6095b3cff
enc cbc(aes) 0x30114b8b79147b3c13c2b7218690b6d2
sel src 0.0.0.0/0 dst 0.0.0.0/0
src 72.21.209.225 dst *my_pub_ip*
proto esp spi 0xb0c07db9 reqid 16385 mode tunnel
replay-window 32
auth hmac(sha1) 0xd344ac06e528c175a9be5c8f7519a9ff4afb17ab
enc cbc(aes) 0x44e6172afdf19dd8a65b216a7af68890
sel src 0.0.0.0/0 dst 0.0.0.0/0
src *my_pub_ip* dst 72.21.209.193
proto esp spi 0x89e3ed52 reqid 16389 mode tunnel
replay-window 32
auth hmac(sha1) 0xaf259a9e3b69ea2d2ca0ce1455f554423cb9b66c
enc cbc(aes) 0x8cf4a967db5f0dde1b57cfe66655c915
sel src 0.0.0.0/0 dst 0.0.0.0/0
src 72.21.209.193 dst *my_pub_ip*
proto esp spi 0x50c171bb reqid 16389 mode tunnel
replay-window 32
auth hmac(sha1) 0x9d3b74757f63d31a4800a57856ae906157c064ef
enc cbc(aes) 0xb37734dc1199d74030032776d2078ddc
sel src 0.0.0.0/0 dst 0.0.0.0/0
ip xfrm policy
src 169.254.255.2/32 dst 169.254.255.1/32
dir out priority 2080 ptype main
tmpl src *my_pub_ip* dst 72.21.209.225
proto esp reqid 16385 mode tunnel
src 169.254.255.1/32 dst 169.254.255.2/32
dir fwd priority 2080 ptype main
tmpl src 72.21.209.225 dst *my_pub_ip*
proto esp reqid 16385 mode tunnel
src 169.254.255.1/32 dst 169.254.255.2/32
dir in priority 2080 ptype main
tmpl src 72.21.209.225 dst *my_pub_ip*
proto esp reqid 16385 mode tunnel
src 169.254.255.6/32 dst 169.254.255.5/32
dir out priority 2080 ptype main
tmpl src *my_pub_ip* dst 72.21.209.193
proto esp reqid 16389 mode tunnel
src 169.254.255.5/32 dst 169.254.255.6/32
dir fwd priority 2080 ptype main
tmpl src 72.21.209.193 dst *my_pub_ip*
proto esp reqid 16389 mode tunnel
src 169.254.255.5/32 dst 169.254.255.6/32
dir in priority 2080 ptype main
tmpl src 72.21.209.193 dst *my_pub_ip*
proto esp reqid 16389 mode tunnel
src ::/0 dst ::/0
dir 4 priority 0 ptype main
src ::/0 dst ::/0
dir 3 priority 0 ptype main
src 0.0.0.0/0 dst 0.0.0.0/0
...
bgpd:
sh ip bgp
...
*> 10.144.0.0/16 169.254.255.1 100 150 7224 i
* 169.254.255.5 100 100 7224 i
...
ip route | grep 10.144
10.144.0.0/16 via 169.254.255.1 dev eth1 proto zebra metric 100
ip route get 10.144.8.30
10.144.8.30 via 169.254.255.1 dev eth1 src 169.254.255.2
cache mtu 1500 advmss 1460 hoplimit 64
ping 10.144.8.30
PING 10.144.8.30 (10.144.8.30) 56(84) bytes of data.
From 169.254.255.2 icmp_seq=1 Destination Host Unreachable
From 169.254.255.2 icmp_seq=2 Destination Host Unreachable
From 169.254.255.2 icmp_seq=3 Destination Host Unreachable
ping -I 10.123.0.22 10.144.8.30
PING 10.144.8.30 (10.144.8.30) from 10.123.0.22 : 56(84) bytes of data.
From 10.123.0.22 icmp_seq=1 Destination Host Unreachable
From 10.123.0.22 icmp_seq=2 Destination Host Unreachable
From 10.123.0.22 icmp_seq=3 Destination Host Unreachable
auth.log
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: loading secrets
from "/etc/ipsec.secrets"
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: loading secrets
from "/var/lib/strongswan/ipsec.secrets.inc"
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: loaded private
key file '/etc/ipsec.d/private/vpn-fw1Key.pem' (1679 bytes)
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: loaded shared
key for 72.21.209.225 *my_pub_ip*
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: loaded shared
key for 72.21.209.193 *my_pub_ip*
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: added connection
description "vac1"
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac1" #1:
initiating Main Mode
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: added connection
description "vac2"
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac2" #2:
initiating Main Mode
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac2" #2:
received Vendor ID payload [Dead Peer Detection]
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac1" #1:
received Vendor ID payload [Dead Peer Detection]
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac2" #2: Peer
ID is ID_IPV4_ADDR: '72.21.209.193'
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac2" #2: ISAKMP
SA established
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac2" #3:
initiating Quick Mode PSK+ENCRYPT+TUNNEL+PFS+UP {using isakmp#2}
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac1" #1: Peer
ID is ID_IPV4_ADDR: '72.21.209.225'
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac1" #1: ISAKMP
SA established
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac1" #4:
initiating Quick Mode PSK+ENCRYPT+TUNNEL+PFS+UP {using isakmp#1}
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac2" #3:
route-client output: /usr/lib/ipsec/_updown: doroute `ip route add
169.254.255.5/32 via 72.21.209.193 dev eth1:MASTER src 169.254.255.6
table 220' failed (RTNETLINK answers: No such process)
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac2" #3: sent
QI2, IPsec SA established {ESP=>0xb660e8f1 <0x11e0e25a}
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac1" #4:
route-client output: /usr/lib/ipsec/_updown: doroute `ip route add
169.254.255.1/32 via 72.21.209.225 dev eth1:MASTER src 169.254.255.2
table 220' failed (RTNETLINK answers: No such process)
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac1" #4: sent
QI2, IPsec SA established {ESP=>0x9545fa88 <0xd79a4539}
Jul 8 15:05:01 vpn-fw1.mdc.gameloft.org CRON[30531]:
pam_unix(cron:session): session opened for user root by (uid=0)
Jul 8 15:05:01 vpn-fw1.mdc.gameloft.org CRON[30532]:
pam_unix(cron:session): session opened for user root by (uid=0)
Jul 8 15:05:01 vpn-fw1.mdc.gameloft.org CRON[30532]:
pam_unix(cron:session): session closed for user root
Jul 8 15:05:02 vpn-fw1.mdc.gameloft.org pluto[30451]: packet from
72.21.209.193:500: received Vendor ID payload [Dead Peer Detection]
Jul 8 15:05:02 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac2" #5:
responding to Main Mode
Jul 8 15:05:02 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac2" #5:
ignoring informational payload, type IPSEC_INITIAL_CONTACT
Jul 8 15:05:02 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac2" #5: Peer
ID is ID_IPV4_ADDR: '72.21.209.193'
Jul 8 15:05:02 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac2" #5: sent
MR3, ISAKMP SA established
Jul 8 15:05:02 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac2" #5: cannot
respond to IPsec SA request because no connection is known for
0.0.0.0/0===*my_pub_ip*...72.21.209.193===0.0.0.0/0
Jul 8 15:05:02 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac2" #5:
sending encrypted notification INVALID_ID_INFORMATION to 72.21.209.193:500
*configuration 2: (10.144/16 work with manual ip xfrm commands)*
ipsec.secrets:
*my_pub_ip* 72.21.209.225 : PSK "*my_psk1*"
*my_pub_ip* 72.21.209.193 : PSK "*my_psk2*"
strongswan.conf:
charon {
}
pluto {
}
libstrongswan {
}
ipsec.conf
conn vac1
keyexchange=ikev1
auto=start
authby=psk
compress=no
type=tunnel
ike=aes128-sha1-modp1024
pfs=yes
left=*my_pub_ip*
leftsubnet=10.0.0.0/8
leftsourceip=169.254.255.2/30
right=72.21.209.225
rightsubnet=10.144.0.0/16
rightsourceip=169.254.255.1/30
conn vac2
keyexchange=ikev1
auto=start
authby=psk
compress=no
type=tunnel
ike=aes128-sha1-modp1024
pfs=yes
left=*my_pub_ip*
leftsubnet=10.0.0.0/8
leftsourceip=169.254.255.6/30
right=72.21.209.193
rightsubnet=10.144.0.0/16
rightsourceip=169.254.255.5/30
sudo /etc/init.d/ipsec start
Starting strongSwan 4.2.4 IPsec [starter]...
multiple default routes - cannot cope with %defaultroute!!!
ip xfrm policy
src 10.0.0.0/8 dst 10.144.0.0/16
dir out priority 2864 ptype main
tmpl src *my_pub_ip* dst 72.21.209.193
proto esp reqid 16389 mode tunnel
src 10.144.0.0/16 dst 10.0.0.0/8
dir fwd priority 2864 ptype main
tmpl src 72.21.209.193 dst *my_pub_ip*
proto esp reqid 16389 mode tunnel
src 10.144.0.0/16 dst 10.0.0.0/8
dir in priority 2864 ptype main
tmpl src 72.21.209.193 dst *my_pub_ip*
proto esp reqid 16389 mode tunnel
src ::/0 dst ::/0
dir 4 priority 0 ptype main
src ::/0 dst ::/0
dir 3 priority 0 ptype main
...
ip route | grep 10.144
*empty*
If I add the following policies:
ip xfrm policy add dir in src 169.254.255.5/30 dst 169.254.255.6/30
priority 2864 tmpl mode tunnel reqid 16389 src 72.21.209.193 dst
*my_pub_ip* proto esp
ip xfrm policy add dir out src 169.254.255.6/30 dst 169.254.255.5/30
priority 2864 tmpl mode tunnel reqid 16389 src *my_pub_ip* dst
72.21.209.193 proto esp
Then the 10.144/16 subnet works
ip route | grep 10.144
10.144.0.0/16 via 169.254.255.5 dev eth1 proto zebra metric 100
ping -I 10.123.0.22 10.144.8.30
PING 10.144.8.30 (10.144.8.30) from 10.123.0.22 : 56(84) bytes of data.
64 bytes from 10.144.8.30: icmp_seq=1 ttl=62 time=17.7 ms
64 bytes from 10.144.8.30: icmp_seq=2 ttl=62 time=17.5 ms
64 bytes from 10.144.8.30: icmp_seq=3 ttl=62 time=17.4 ms
auth.log
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: loading secrets
from "/etc/ipsec.secrets"
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: loading secrets
from "/var/lib/strongswan/ipsec.secrets.inc"
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: loaded private
key file '/etc/ipsec.d/private/vpn-fw1Key.pem' (1679 bytes)
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: loaded shared
key for 72.21.209.225 *my_pub_ip*
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: loaded shared
key for 72.21.209.193 *my_pub_ip*
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: added connection
description "vac1"
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac1" #1:
initiating Main Mode
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: added connection
description "vac2"
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac2" #2:
initiating Main Mode
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac2" #2:
received Vendor ID payload [Dead Peer Detection]
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac1" #1:
received Vendor ID payload [Dead Peer Detection]
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac2" #2: Peer
ID is ID_IPV4_ADDR: '72.21.209.193'
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac2" #2: ISAKMP
SA established
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac2" #3:
initiating Quick Mode PSK+ENCRYPT+TUNNEL+PFS+UP {using isakmp#2}
src 169.254.255.6 table 220' failed (RTNETLINK answers: No such process)
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac2" #3: sent
QI2, IPsec SA established {ESP=>0x6705b3eb <0x945af92b}
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac1" #1: Peer
ID is ID_IPV4_ADDR: '72.21.209.225'
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac1" #1: ISAKMP
SA established
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac1" #4:
initiating Quick Mode PSK+ENCRYPT+TUNNEL+PFS+UP {using isakmp#1}
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac1" #4: cannot
route -- route already in use for "vac2"
Jul 8 14:44:26 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac1" #4: cannot
route -- route already in use for "vac2"
Jul 8 14:44:31 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac1" #4: cannot
route -- route already in use for "vac2"
Jul 8 14:44:36 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac1" #4: cannot
route -- route already in use for "vac2"
Jul 8 14:44:46 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac1" #4: cannot
route -- route already in use for "vac2"
Jul 8 14:44:56 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac1" #4: cannot
route -- route already in use for "vac2"
[Attachment #7 (text/html)]
<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN">
<html>
<head>
<meta content="text/html; charset=ISO-8859-1"
http-equiv="Content-Type">
</head>
<body bgcolor="#ffffff" text="#000000">
Hi, I'm trying to connect to amazon VPN using strongswan 4.2.4 on
debian 5.0.8 but I have some problems.<br>
<br>
Here is how the setup is designed from amazon side.<br>
Amazon have 2 public IP addresses and we connect to the 2 ips using
2 distinct vpn connection. However those connection are initiated
(on our side) by only 1 server. So we use the same public ip address
on our side.<br>
<br>
So we establish the connection with the following subnets
169.254.255.0/30 and 169.254.255.4/30 (one for each vpn connection).
<br>
So far, I'm able to make this connection up and running. The problem
comes when I need to route other subnets to this VPN connection with
BGP. In my case I defined on amazon side the following subnet:
10.144.0.0/16. But when I try to use this subnet the packets don't
seem to be routed to the tunnel. Of course bgp is up and the routes
are added by bgp.<br>
<br>
I've been able to make the setup work with manual commands and weird
(to me since i'm far from beeing an expert on ipsec/ike)
configuration. But i'm pretty sure there is a clean way to make this
works without too much problems.<br>
<br>
Could you please help me on how to setup this connection properly?<br>
Thank you.<br>
<br>
Here are the 2 configuration settings I've been able to use to bring
up the vpn connection. The 1st one can't route the 10.144/16 network
even though I add xfrm policies, and the 2nd one is working, but
only one vpn comes up because it can't add the same route on the 2
vpn connections and I have to run some ip xfrm commands to make it
work.<br>
<br>
Here is the amazon VPN Connection Configuration<br>
<br>
<b>connection 1:</b><br>
Outside IP Addresses:<br>
- Customer Gateway: : \
*my_pub_ip*<br> - VPN \
Gateway \
: 72.21.209.225<br> <br>
Inside IP Addresses<br>
- Customer Gateway : \
169.254.255.2/30<br> - VPN \
Gateway \
: 169.254.255.1/30<br> <br>
Configure the IKE SA as follows<br>
- Authentication Method : Pre-Shared Key <br>
- Pre-Shared \
Key : *my_psk1*<br> \
- Authentication Algorithm : sha1<br> - Encryption \
Algorithm : aes-128-cbc<br> - \
Lifetime \
: 28800 seconds<br> - Phase 1 Negotiation Mode : main<br>
- Perfect Forward Secrecy : Diffie-Hellman Group 2<br>
<br>
Configure the IPSec SA as follows:<br>
- Protocol \
: esp<br> - Authentication Algorithm : hmac-sha1-96<br>
- Encryption Algorithm : aes-128-cbc<br>
- Lifetime \
: 3600 seconds<br> - \
Mode \
: tunnel<br> - Perfect Forward Secrecy : Diffie-Hellman Group 2<br>
<br>
The Border Gateway Protocol (BGPv4) is used within the tunnel,
between the inside<br>
IP addresses, to exchange routes from the VPC to your home network.
Each<br>
BGP router has an Autonomous System Number (ASN). Your ASN was
provided <br>
to AWS when the Customer Gateway was created.<br>
<br>
BGP Configuration Options:<br>
- Customer Gateway ASN : 65136 <br>
- VPN Gateway ASN : \
7224<br> - Neighbor IP Address : \
169.254.255.1<br> - Neighbor Hold Time : \
30<br> <br>
Configure BGP to announce the default route (0.0.0.0/0) to the VPN
Connection<br>
Gateway. The VPN Gateway will announce prefixes to your Customer <br>
Gateway based upon the prefixes assigned in the creation of the VPC.<br>
<br>
<br>
<b>Connection 2:</b><br>
<br>
Outside IP Addresses:<br>
- Customer Gateway: : \
*my_pub_ip*<br> - VPN \
Gateway \
: 72.21.209.193<br> <br>
Inside IP Addresses<br>
- Customer Gateway : \
169.254.255.6/30<br> - VPN \
Gateway \
: 169.254.255.5/30<br> <br>
Configure the IKE SA as follows<br>
- Authentication Method : Pre-Shared Key <br>
- Pre-Shared \
Key : *my_psk2*<br> \
- Authentication Algorithm : sha1<br> - Encryption \
Algorithm : aes-128-cbc<br> - \
Lifetime \
: 28800 seconds<br> - Phase 1 Negotiation Mode : main<br>
- Perfect Forward Secrecy : Diffie-Hellman Group 2<br>
<br>
Configure the IPSec SA as follows:<br>
- Protocol \
: esp<br> - Authentication Algorithm : hmac-sha1-96<br>
- Encryption Algorithm : aes-128-cbc<br>
- Lifetime \
: 3600 seconds<br> - \
Mode \
: tunnel<br> - Perfect Forward Secrecy : Diffie-Hellman Group 2<br>
<br>
<br>
The Border Gateway Protocol (BGPv4) is used within the tunnel,
between the inside<br>
IP addresses, to exchange routes from the VPC to your home network.
Each<br>
BGP router has an Autonomous System Number (ASN). Your ASN was
provided <br>
to AWS when the Customer Gateway was created.<br>
<br>
BGP Configuration Options:<br>
- Customer Gateway ASN : 65136 <br>
- VPN Gateway ASN : \
7224<br> - Neighbor IP Address : \
169.254.255.5<br> - Neighbor Hold Time : \
30<br> <br>
Configure BGP to announce the default route (0.0.0.0/0) to the VPN
Connection<br>
Gateway. The VPN Gateway will announce prefixes to your Customer <br>
Gateway based upon the prefixes assigned in the creation of the VPC.<br>
<br>
<br>
And here is the configuration I've been trying to setup.<br>
<br>
<b>configuration 1: (10.144/16 not working at all)</b><br>
ipsec.secrets:<br>
*my_pub_ip* 72.21.209.225 : PSK "*my_psk1*"<br>
*my_pub_ip* 72.21.209.193 : PSK "*my_psk2*"<br>
<br>
strongswan.conf:<br>
charon {<br>
}<br>
pluto {<br>
}<br>
libstrongswan {<br>
}<br>
<br>
ipsec.conf<br>
config setup<br>
charonstart=no<br>
plutostart=yes<br>
strictcrlpolicy=no<br>
<br>
conn vac1<br>
keyexchange=ikev1<br>
auto=start<br>
authby=psk<br>
compress=no<br>
type=tunnel<br>
ike=aes128-sha1-modp1024<br>
pfs=yes<br>
left=*my_pub_ip*<br>
leftsourceip=169.254.255.2/30<br>
right=72.21.209.225<br>
rightsourceip=169.254.255.1/30<br>
<br>
conn vac2<br>
keyexchange=ikev1<br>
auto=start<br>
authby=psk<br>
compress=no<br>
type=tunnel<br>
ike=aes128-sha1-modp1024<br>
pfs=yes<br>
left=*my_pub_ip*<br>
leftsourceip=169.254.255.6/30<br>
right=72.21.209.193<br>
rightsourceip=169.254.255.5/30<br>
<br>
sudo /etc/init.d/ipsec start<br>
Starting strongSwan 4.2.4 IPsec [starter]...<br>
multiple default routes - cannot cope with %defaultroute!!!<br>
<br>
ip xfrm state<br>
src *my_pub_ip* dst 72.21.209.225<br>
proto esp spi 0xd49408d7 reqid 16385 mode tunnel<br>
replay-window 32 <br>
auth hmac(sha1) 0x3696cf0b7cbd526edf0b8793084334a6095b3cff<br>
enc cbc(aes) 0x30114b8b79147b3c13c2b7218690b6d2<br>
sel src 0.0.0.0/0 dst 0.0.0.0/0 <br>
src 72.21.209.225 dst *my_pub_ip*<br>
proto esp spi 0xb0c07db9 reqid 16385 mode tunnel<br>
replay-window 32 <br>
auth hmac(sha1) 0xd344ac06e528c175a9be5c8f7519a9ff4afb17ab<br>
enc cbc(aes) 0x44e6172afdf19dd8a65b216a7af68890<br>
sel src 0.0.0.0/0 dst 0.0.0.0/0 <br>
src *my_pub_ip* dst 72.21.209.193<br>
proto esp spi 0x89e3ed52 reqid 16389 mode tunnel<br>
replay-window 32 <br>
auth hmac(sha1) 0xaf259a9e3b69ea2d2ca0ce1455f554423cb9b66c<br>
enc cbc(aes) 0x8cf4a967db5f0dde1b57cfe66655c915<br>
sel src 0.0.0.0/0 dst 0.0.0.0/0 <br>
src 72.21.209.193 dst *my_pub_ip*<br>
proto esp spi 0x50c171bb reqid 16389 mode tunnel<br>
replay-window 32 <br>
auth hmac(sha1) 0x9d3b74757f63d31a4800a57856ae906157c064ef<br>
enc cbc(aes) 0xb37734dc1199d74030032776d2078ddc<br>
sel src 0.0.0.0/0 dst 0.0.0.0/0 <br>
<br>
ip xfrm policy<br>
src 169.254.255.2/32 dst 169.254.255.1/32 <br>
dir out priority 2080 ptype main <br>
tmpl src *my_pub_ip* dst 72.21.209.225<br>
proto esp reqid 16385 mode tunnel<br>
src 169.254.255.1/32 dst 169.254.255.2/32 <br>
dir fwd priority 2080 ptype main <br>
tmpl src 72.21.209.225 dst *my_pub_ip*<br>
proto esp reqid 16385 mode tunnel<br>
src 169.254.255.1/32 dst 169.254.255.2/32 <br>
dir in priority 2080 ptype main <br>
tmpl src 72.21.209.225 dst *my_pub_ip*<br>
proto esp reqid 16385 mode tunnel<br>
src 169.254.255.6/32 dst 169.254.255.5/32 <br>
dir out priority 2080 ptype main <br>
tmpl src *my_pub_ip* dst 72.21.209.193<br>
proto esp reqid 16389 mode tunnel<br>
src 169.254.255.5/32 dst 169.254.255.6/32 <br>
dir fwd priority 2080 ptype main <br>
tmpl src 72.21.209.193 dst *my_pub_ip*<br>
proto esp reqid 16389 mode tunnel<br>
src 169.254.255.5/32 dst 169.254.255.6/32 <br>
dir in priority 2080 ptype main <br>
tmpl src 72.21.209.193 dst *my_pub_ip*<br>
proto esp reqid 16389 mode tunnel<br>
src ::/0 dst ::/0 <br>
dir 4 priority 0 ptype main <br>
src ::/0 dst ::/0 <br>
dir 3 priority 0 ptype main <br>
src 0.0.0.0/0 dst 0.0.0.0/0 <br>
...<br>
<br>
bgpd:<br>
sh ip bgp<br>
...<br>
*> 10.144.0.0/16 \
169.254.255.1 \
100 150 7224 i<br>
* \
169.254.255.5 \
100 100 \
7224 i<br>
...<br>
<br>
ip route | grep 10.144<br>
10.144.0.0/16 via 169.254.255.1 dev eth1 proto zebra metric 100 <br>
<br>
ip route get 10.144.8.30<br>
10.144.8.30 via 169.254.255.1 dev eth1 src 169.254.255.2 <br>
cache mtu 1500 advmss 1460 hoplimit 64<br>
<br>
ping 10.144.8.30<br>
PING 10.144.8.30 (10.144.8.30) 56(84) bytes of data.<br>
From 169.254.255.2 icmp_seq=1 Destination Host Unreachable<br>
From 169.254.255.2 icmp_seq=2 Destination Host Unreachable<br>
From 169.254.255.2 icmp_seq=3 Destination Host Unreachable<br>
<br>
ping -I 10.123.0.22 10.144.8.30<br>
PING 10.144.8.30 (10.144.8.30) from 10.123.0.22 : 56(84) bytes of
data.<br>
From 10.123.0.22 icmp_seq=1 Destination Host Unreachable<br>
From 10.123.0.22 icmp_seq=2 Destination Host Unreachable<br>
From 10.123.0.22 icmp_seq=3 Destination Host Unreachable<br>
<br>
auth.log<br>
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: loading
secrets from "/etc/ipsec.secrets"<br>
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: loading
secrets from "/var/lib/strongswan/ipsec.secrets.inc"<br>
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: loaded
private key file '/etc/ipsec.d/private/vpn-fw1Key.pem' (1679 bytes)<br>
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: loaded
shared key for 72.21.209.225 *my_pub_ip* <br>
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: loaded
shared key for 72.21.209.193 *my_pub_ip* <br>
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: added
connection description "vac1"<br>
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac1" #1:
initiating Main Mode<br>
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: added
connection description "vac2"<br>
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac2" #2:
initiating Main Mode<br>
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac2" #2:
received Vendor ID payload [Dead Peer Detection]<br>
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac1" #1:
received Vendor ID payload [Dead Peer Detection]<br>
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac2" #2:
Peer ID is ID_IPV4_ADDR: '72.21.209.193'<br>
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac2" #2:
ISAKMP SA established<br>
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac2" #3:
initiating Quick Mode PSK+ENCRYPT+TUNNEL+PFS+UP {using isakmp#2}<br>
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac1" #1:
Peer ID is ID_IPV4_ADDR: '72.21.209.225'<br>
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac1" #1:
ISAKMP SA established<br>
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac1" #4:
initiating Quick Mode PSK+ENCRYPT+TUNNEL+PFS+UP {using isakmp#1}<br>
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac2" #3:
route-client output: /usr/lib/ipsec/_updown: doroute `ip route add
169.254.255.5/32 via 72.21.209.193 dev eth1:MASTER src
169.254.255.6 table 220' failed (RTNETLINK answers: No such process)<br>
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac2" #3:
sent QI2, IPsec SA established {ESP=>0xb660e8f1 <0x11e0e25a}<br>
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac1" #4:
route-client output: /usr/lib/ipsec/_updown: doroute `ip route add
169.254.255.1/32 via 72.21.209.225 dev eth1:MASTER src
169.254.255.2 table 220' failed (RTNETLINK answers: No such process)<br>
Jul 8 15:04:58 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac1" #4:
sent QI2, IPsec SA established {ESP=>0x9545fa88 <0xd79a4539}<br>
Jul 8 15:05:01 vpn-fw1.mdc.gameloft.org CRON[30531]:
pam_unix(cron:session): session opened for user root by (uid=0)<br>
Jul 8 15:05:01 vpn-fw1.mdc.gameloft.org CRON[30532]:
pam_unix(cron:session): session opened for user root by (uid=0)<br>
Jul 8 15:05:01 vpn-fw1.mdc.gameloft.org CRON[30532]:
pam_unix(cron:session): session closed for user root<br>
Jul 8 15:05:02 vpn-fw1.mdc.gameloft.org pluto[30451]: packet from
72.21.209.193:500: received Vendor ID payload [Dead Peer Detection]<br>
Jul 8 15:05:02 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac2" #5:
responding to Main Mode<br>
Jul 8 15:05:02 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac2" #5:
ignoring informational payload, type IPSEC_INITIAL_CONTACT<br>
Jul 8 15:05:02 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac2" #5:
Peer ID is ID_IPV4_ADDR: '72.21.209.193'<br>
Jul 8 15:05:02 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac2" #5:
sent MR3, ISAKMP SA established<br>
Jul 8 15:05:02 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac2" #5:
cannot respond to IPsec SA request because no connection is known
for 0.0.0.0/0===*my_pub_ip*...72.21.209.193===0.0.0.0/0<br>
Jul 8 15:05:02 vpn-fw1.mdc.gameloft.org pluto[30451]: "vac2" #5:
sending encrypted notification INVALID_ID_INFORMATION to
72.21.209.193:500<br>
<br>
<b>configuration 2: (10.144/16 work with manual ip xfrm commands)</b><br>
ipsec.secrets:<br>
*my_pub_ip* 72.21.209.225 : PSK "*my_psk1*"<br>
*my_pub_ip* 72.21.209.193 : PSK "*my_psk2*"<br>
<br>
strongswan.conf:<br>
charon {<br>
}<br>
pluto {<br>
}<br>
libstrongswan {<br>
}<br>
<br>
ipsec.conf<br>
conn vac1<br>
keyexchange=ikev1<br>
auto=start<br>
authby=psk<br>
compress=no<br>
type=tunnel<br>
ike=aes128-sha1-modp1024<br>
pfs=yes<br>
left=*my_pub_ip*<br>
leftsubnet=10.0.0.0/8<br>
leftsourceip=169.254.255.2/30<br>
right=72.21.209.225<br>
rightsubnet=10.144.0.0/16<br>
rightsourceip=169.254.255.1/30<br>
<br>
conn vac2<br>
keyexchange=ikev1<br>
auto=start<br>
authby=psk<br>
compress=no<br>
type=tunnel<br>
ike=aes128-sha1-modp1024<br>
pfs=yes<br>
left=*my_pub_ip*<br>
leftsubnet=10.0.0.0/8<br>
leftsourceip=169.254.255.6/30<br>
right=72.21.209.193<br>
rightsubnet=10.144.0.0/16<br>
rightsourceip=169.254.255.5/30<br>
<br>
sudo /etc/init.d/ipsec start<br>
Starting strongSwan 4.2.4 IPsec [starter]...<br>
multiple default routes - cannot cope with %defaultroute!!!<br>
<br>
<br>
ip xfrm policy<br>
src 10.0.0.0/8 dst 10.144.0.0/16 <br>
dir out priority 2864 ptype main <br>
tmpl src *my_pub_ip* dst 72.21.209.193<br>
proto esp reqid 16389 mode tunnel<br>
src 10.144.0.0/16 dst 10.0.0.0/8 <br>
dir fwd priority 2864 ptype main <br>
tmpl src 72.21.209.193 dst *my_pub_ip*<br>
proto esp reqid 16389 mode tunnel<br>
src 10.144.0.0/16 dst 10.0.0.0/8 <br>
dir in priority 2864 ptype main <br>
tmpl src 72.21.209.193 dst *my_pub_ip*<br>
proto esp reqid 16389 mode tunnel<br>
src ::/0 dst ::/0 <br>
dir 4 priority 0 ptype main <br>
src ::/0 dst ::/0 <br>
dir 3 priority 0 ptype main<br>
...<br>
<br>
ip route | grep 10.144<br>
*empty*<br>
<br>
If I add the following policies:<br>
ip xfrm policy add dir in src 169.254.255.5/30 dst 169.254.255.6/30
priority 2864 tmpl mode tunnel reqid 16389 src 72.21.209.193 dst
*my_pub_ip* proto esp<br>
ip xfrm policy add dir out src 169.254.255.6/30 dst 169.254.255.5/30
priority 2864 tmpl mode tunnel reqid 16389 src *my_pub_ip* dst
72.21.209.193 proto esp<br>
<br>
<br>
Then the 10.144/16 subnet works<br>
<br>
ip route | grep 10.144<br>
10.144.0.0/16 via 169.254.255.5 dev eth1 proto zebra metric 100 <br>
<br>
<br>
ping -I 10.123.0.22 10.144.8.30<br>
PING 10.144.8.30 (10.144.8.30) from 10.123.0.22 : 56(84) bytes of
data.<br>
64 bytes from 10.144.8.30: icmp_seq=1 ttl=62 time=17.7 ms<br>
64 bytes from 10.144.8.30: icmp_seq=2 ttl=62 time=17.5 ms<br>
64 bytes from 10.144.8.30: icmp_seq=3 ttl=62 time=17.4 ms<br>
<br>
auth.log<br>
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: loading
secrets from "/etc/ipsec.secrets"<br>
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: loading
secrets from "/var/lib/strongswan/ipsec.secrets.inc"<br>
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: loaded
private key file '/etc/ipsec.d/private/vpn-fw1Key.pem' (1679 bytes)<br>
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: loaded
shared key for 72.21.209.225 *my_pub_ip* <br>
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: loaded
shared key for 72.21.209.193 *my_pub_ip* <br>
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: added
connection description "vac1"<br>
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac1" #1:
initiating Main Mode<br>
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: added
connection description "vac2"<br>
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac2" #2:
initiating Main Mode<br>
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac2" #2:
received Vendor ID payload [Dead Peer Detection]<br>
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac1" #1:
received Vendor ID payload [Dead Peer Detection]<br>
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac2" #2:
Peer ID is ID_IPV4_ADDR: '72.21.209.193'<br>
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac2" #2:
ISAKMP SA established<br>
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac2" #3:
initiating Quick Mode PSK+ENCRYPT+TUNNEL+PFS+UP {using isakmp#2}<br>
src 169.254.255.6 table 220' failed (RTNETLINK answers: No such
process)<br>
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac2" #3:
sent QI2, IPsec SA established {ESP=>0x6705b3eb <0x945af92b}<br>
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac1" #1:
Peer ID is ID_IPV4_ADDR: '72.21.209.225'<br>
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac1" #1:
ISAKMP SA established<br>
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac1" #4:
initiating Quick Mode PSK+ENCRYPT+TUNNEL+PFS+UP {using isakmp#1}<br>
Jul 8 14:44:21 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac1" #4:
cannot route -- route already in use for "vac2"<br>
Jul 8 14:44:26 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac1" #4:
cannot route -- route already in use for "vac2"<br>
Jul 8 14:44:31 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac1" #4:
cannot route -- route already in use for "vac2"<br>
Jul 8 14:44:36 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac1" #4:
cannot route -- route already in use for "vac2"<br>
Jul 8 14:44:46 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac1" #4:
cannot route -- route already in use for "vac2"<br>
Jul 8 14:44:56 vpn-fw1.mdc.gameloft.org pluto[25503]: "vac1" #4:
cannot route -- route already in use for "vac2"<br>
<br>
<div class="moz-signature"><br>
</div>
</body>
</html>
["signature.asc" (application/pgp-signature)]
_______________________________________________
Users mailing list
Users@lists.strongswan.org
https://lists.strongswan.org/mailman/listinfo/users
[prev in list] [next in list] [prev in thread] [next in thread]
Configure |
About |
News |
Add a list |
Sponsored by KoreLogic