[prev in list] [next in list] [prev in thread] [next in thread]
List: openbsd-bugs
Subject: unable to boot current 4.8-beta on a very old laptop
From: beasley <beasley () hiwaay ! net>
Date: 2010-07-31 19:28:54
Message-ID: 1280604534.8099.59.camel () sundog
[Download RAW message or body]
My ancient Pentium laptop currently has 4.7-release installed.
A couple days ago I tried to install the July 26th snapshot of
current without success. When I boot from the install.iso CD-R
media I get most of the way through the boot sequence and then
suddenly the machine resets and begins to boot all over again.
This continues endlessly until I remove the CD media.
I tried again today with the July 28th snapshot of current and
got the same behavior. I don't believe I have any hardware
problems as the OpenBSD 4.7 installation on the hard drive
boots normally and I can pass MemTest86+ memory diagnostics.
I hooked up a null-modem RS232 cable between the laptop and
another machine to try to capture the boot messages before the
laptop resets. I've set the baud rate to 115200 on both ends.
To provide an apples-to-apples comparison I booted the machine
from an official 4.7 release CD. Here's the captured results:
-------------------------------------------------------------
>> OpenBSD/i386 CDBOOT 2.02
boot>
booting cd0a:/4.7/i386/bsd.rd: 5864788+916112 [52+221040
+208132]=0x6e0600
entry point at 0x200120
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights
reserved.
Copyright (c) 1995-2010 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 4.7 (RAMDISK_CD) #353: Wed Mar 17 21:02:53 MDT 2010
deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/RAMDISK_CD
cpu0: Intel Pentium/MMX ("GenuineIntel" 586-class) 267 MHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,MCE,CX8,MMX
real mem = 167407616 (159MB)
avail mem = 155385856 (148MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 12/28/99, BIOS32 rev. 0 @ 0xfe95a
apm0 at bios0: Power Management spec V1.2
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf8e80/96 (4 entries)
pcibios0: no compatible PCI ICU found: ICU vendor 0xffff product 0xffff
pcibios0: Warning, unable to fix up PCI interrupt routing
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc0000/0x9800
cpu0 at mainbus0: (uniprocessor)
cpu0: F00F bug workaround installed
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Toshiba PCI" rev 0xa0
vga1 at pci0 dev 4 function 0 "Chips and Technologies 65555" rev 0xc6
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
ohci0 at pci0 dev 11 function 0 "NEC USB" rev 0x02: irq 11, version 1.0
"Toshiba Fast Infrared Type O" rev 0x21 at pci0 dev 17 function 0 not
configured
usb0 at ohci0: USB revision 1.0
uhub0 at usb0 "NEC OHCI root hub" rev 1.00/1.00 addr 1
isa0 at mainbus0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
wdc0 at isa0 port 0x1f0/8 irq 14
wd0 at wdc0 channel 0 drive 0: <IBM-DTCA-24090>
wd0: 16-sector PIO, LBA, 3909MB, 8007552 sectors
wd0(wdc0:0:0): using BIOS timings
wdc1 at isa0 port 0x170/8 irq 15
atapiscsi0 at wdc1 channel 0 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <TEAC, CD-220EA, 7.1B> ATAPI 5/cdrom
removable
cd0(wdc1:0:0): using BIOS timings
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
pcic0 at isa0 port 0x3e0/2 iomem 0xd0000/16384
pcic0 controller 0: <Intel 82365SL rev 1> has sockets A and B
pcmcia0 at pcic0 controller 0 socket 0
pcmcia1 at pcic0 controller 0 socket 1
pcic0: irq 3, polling enabled
biomask ffe5 netmask ffe5 ttymask ffff
rd0: fixed, 3800 blocks
softraid0 at root
root on rd0a swap on rd0b dump on rd0b
erase ^?, werase ^W, kill ^U, intr ^C, status ^T
Welcome to the OpenBSD/i386 4.7 installation program.
(I)nstall, (U)pgrade or (S)hell?
-------------------------------------------------------------
Now here's the capture from the 4.8-Beta (07/28/10) snapshot:
-------------------------------------------------------------
>> OpenBSD/i386 CDBOOT 3.14
boot>
booting cd0a:/4.8/i386/bsd.rd: 5877360+942772 [61+224560
+212522]=0x6ebe5c
entry point at 0x200120
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights
reserved.
Copyright (c) 1995-2010 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 4.8-beta (RAMDISK_CD) #49: Wed Jul 28 18:35:55 MDT 2010
deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/RAMDISK_CD
cpu0: Intel Pentium/MMX ("GenuineIntel" 586-class) 267 MHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,MCE,CX8,MMX
real mem = 167407616 (159MB)
avail mem = 157798400 (150MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 12/28/99, BIOS32 rev. 0 @ 0xfe95a
apm0 at bios0: Power Management spec V1.2
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf8e80/96 (4 entries)
pcibios0: no compatible PCI ICU found: ICU vendor 0xffff product 0xffff
pcibios0: Warning, unable to fix up PCI interrupt routing
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc0000/0x9800
cpu0 at mainbus0: (uniprocessor)
cpu0: F00F bug workaround installed
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Toshiba PCI" rev 0xa0
vga1 at pci0 dev 4 function 0 "Chips and Technologies 65555" rev 0xc6
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
ohci0 at pci0 dev 11 function 0 "NEC USB" rev 0x02: irq 11, version 1.0
"Toshiba Fast Infrared Type O" rev 0x21 at pci0 dev 17 function 0 not
configured
usb0 at ohci0: USB revision 1.0
uhub0 at usb0 "NEC OHCI root hub" rev 1.00/1.00 addr 1
isa0 at mainbus0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
wdc0 at isa0 port 0x1f0/8 irq 14
wd0 at wdc0 channel 0 drive 0: <IBM-DTCA-24090>
wd0: 16-sector PIO, LBA, 3909MB, 8007552 sectors
wd0(wdc0:0:0): using BIOS timings
wdc1 at isa0 port 0x170/8 irq 15
atapiscsi0 at wdc1 channel 0 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <TEAC, CD-220EA, 7.1B> ATAPI 5/cdrom
removable
cd0(wdc1:0:0): using BIOS timings
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
pcic0 at isa0 port 0x3e0/2 iomem 0xd0000/16384
pcic0 controller 0: <Intel 82365SL rev 1> has sockets A and B
pcmcia0 at pcic0 controller 0 socket 0
pcmcia1 at pcic0 controller 0 socket 1
pcic0: irq 3, polling enabled
biomask ffe5 netmask ffe5 ttymask ffff
rd0: fixed, 3800 blocks
-------------------------------------------------------------
There's no further serial data output and about 1 second later
the laptop resets and I see the BIOS splash screen come up.
A diff between these two output files isn't very helpful:
1c1
< >> OpenBSD/i386 CDBOOT 2.02
---
> >> OpenBSD/i386 CDBOOT 3.14
3c3
< booting cd0a:/4.7/i386/bsd.rd: 5864788+916112 [52+221040
+208132]=0x6e0600
---
> booting cd0a:/4.8/i386/bsd.rd: 5877360+942772 [61+224560
+212522]=0x6ebe5c
10c10
< OpenBSD 4.7 (RAMDISK_CD) #353: Wed Mar 17 21:02:53 MDT 2010
---
> OpenBSD 4.8-beta (RAMDISK_CD) #49: Wed Jul 28 18:35:55 MDT 2010
15c15
< avail mem = 155385856 (148MB)
---
> avail mem = 157798400 (150MB)
62,67d61
< softraid0 at root
< root on rd0a swap on rd0b dump on rd0b
< erase ^?, werase ^W, kill ^U, intr ^C, status ^T
<
< Welcome to the OpenBSD/i386 4.7 installation program.
< (I)nstall, (U)pgrade or (S)hell?
-------------------------------------------------------------
The only thing else I can think of to send along at this
point is a dmesg file from the hard-drive installed 4.7
release after its normal boot. So here's that output:
-------------------------------------------------------------
OpenBSD 4.7 (GENERIC) #558: Wed Mar 17 20:46:15 MDT 2010
deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium/MMX ("GenuineIntel" 586-class) 267 MHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,MCE,CX8,MMX
real mem = 167407616 (159MB)
avail mem = 153554944 (146MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 12/28/99, BIOS32 rev. 0 @ 0xfe95a
apm0 at bios0: Power Management spec V1.2
apm0: battery life expectancy 100%
apm0: AC on, battery charge high, estimated 2:42 hours
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf8e80/96 (4 entries)
pcibios0: no compatible PCI ICU found: ICU vendor 0xffff product 0xffff
pcibios0: Warning, unable to fix up PCI interrupt routing
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc0000/0x9800
cpu0 at mainbus0: (uniprocessor)
cpu0: F00F bug workaround installed
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Toshiba PCI" rev 0xa0
vga1 at pci0 dev 4 function 0 "Chips and Technologies 65555" rev 0xc6
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
ohci0 at pci0 dev 11 function 0 "NEC USB" rev 0x02: irq 11, version 1.0
"Toshiba Fast Infrared Type O" rev 0x21 at pci0 dev 17 function 0 not
configured
usb0 at ohci0: USB revision 1.0
uhub0 at usb0 "NEC OHCI root hub" rev 1.00/1.00 addr 1
isa0 at mainbus0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
wdc0 at isa0 port 0x1f0/8 irq 14
wd0 at wdc0 channel 0 drive 0: <IBM-DTCA-24090>
wd0: 16-sector PIO, LBA, 3909MB, 8007552 sectors
wd0(wdc0:0:0): using BIOS timings
wdc1 at isa0 port 0x170/8 irq 15
atapiscsi0 at wdc1 channel 0 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <TEAC, CD-220EA, 7.1B> ATAPI 5/cdrom
removable
cd0(wdc1:0:0): using BIOS timings
sb0 at isa0 port 0x220/24 irq 5 drq 1: dsp v3.01
midi0 at sb0: <SB MIDI UART>
audio0 at sb0
opl0 at sb0: model OPL3
midi1 at opl0: <SB Yamaha OPL3>
wss0 at isa0 port 0x530/8 irq 10 drq 0: CS4231 or AD1845 (vers 4)
audio1 at wss0
pcppi0 at isa0 port 0x61
midi2 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
pcic0 at isa0 port 0x3e0/2 iomem 0xd0000/65536
pcic0 controller 0: <Intel 82365SL rev 1> has sockets A and B
pcmcia0 at pcic0 controller 0 socket 0
pcmcia1 at pcic0 controller 0 socket 1
pcic0: irq 3, polling enabled
biomask eb45 netmask eb45 ttymask fbdf
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
-------------------------------------------------------------
Thanks for looking into this bug. If there's anything at all
I can do to help diagnose this trouble please let me know.
Michael Beasley
[prev in list] [next in list] [prev in thread] [next in thread]
Configure |
About |
News |
Add a list |
Sponsored by KoreLogic