[prev in list] [next in list] [prev in thread] [next in thread]
List: openbsd-arm
Subject: Re: current on BeagleBone Black
From: Jan Stary <hans () stare ! cz>
Date: 2014-02-16 11:11:50
Message-ID: 20140216111149.GA6469 () www ! stare ! cz
[Download RAW message or body]
On Feb 16 11:40:16, hans@stare.cz wrote:
> The reason I am installing onto the internal flash at all
> is that I can't install on a separate microSD card: I am
> *always* getting i/o errors that make the install fail.
This is the whole script, see the IO errors at bottom.
I have tortured the card in my laptop, and never got
an error during that ...
Jan
U-Boot SPL 2013.04-dirty (Apr 20 2013 - 08:30:43)
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
OMAP SD/MMC: 0
mmc_send_cmd : timeout: No status update
reading u-boot.img
reading u-boot.img
U-Boot 2013.04-dirty (Apr 20 2013 - 08:30:43)
I2C: ready
DRAM: 512 MiB
WARNING: Caches not enabled
NAND: No NAND device found!!!
0 MiB
MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Warning - readenv() failed, using default environment
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
Net: <ethaddr> not set. Validating first E-fuse MAC
Phy not found
PHY reset timed out
cpsw, usb_ether
Hit any key to stop autoboot: 0
gpio: pin 53 (gpio 53) value is 1
mmc0 is current device
micro SD card found
mmc0 is current device
gpio: pin 54 (gpio 54) value is 1
SD/MMC found on device 0
reading uEnv.txt
151 bytes read in 3 ms (48.8 KiB/s)
Loaded environment from uEnv.txt
Importing environment from mmc ...
Running uenvcmd ...
reading bsd.umg
7325260 bytes read in 842 ms (8.3 MiB/s)
## Booting kernel from Legacy Image at 82800000 ...
Image Name: boot
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 7325196 Bytes = 7 MiB
Load Address: 80300000
Entry Point: 80300000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
OpenBSD/omap booting ...
arg0 0x0 arg1 0xe05 arg2 0x80000100
atag core flags 0 pagesize 0 rootdev 0
atag cmdline [sd0i:/bsd.umg]
atag mem start 0x80000000 size 0x20000000
bootfile: sd0i:/bsd.umg
bootargs:
memory size derived from u-boot
bootconf.mem[0].address = 80000000 pages 131072/0x20000000
Allocating page tables
freestart = 0x809fd000, free_pages = 128515 (0x0001f603)
IRQ stack: p0x80a2b000 v0xc0a2b000
ABT stack: p0x80a2c000 v0xc0a2c000
UND stack: p0x80a2d000 v0xc0a2d000
SVC stack: p0x80a2e000 v0xc0a2e000
Creating L1 page table at 0x80a00000
Mapping kernel
Constructing L2 page tables
undefined page pmap [ using 171196 bytes of bsd ELF symbol table ]
board type: beaglebone
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2014 OpenBSD. All rights reserved. http://www.OpenBSD.org
OpenBSD 5.5-beta (RAMDISK-OMAP) #4: Thu Feb 6 00:43:16 EST 2014
root@bbb1.openbsd.org:/usr/src/sys/arch/armv7/compile/RAMDISK-OMAP
real mem = 536870912 (512MB)
avail mem = 515280896 (491MB)
warning: no entropy supplied by boot loader
mainbus0 at root
cpu0 at mainbus0: ARM Cortex A8 R3 rev 2 (ARMv7 core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(64b/l,4way) I-cache, 32KB(64b/l,4way) wr-back D-cache
omap0 at mainbus0: BeagleBone
prcm0 at omap0 rev 0.2
sitaracm0 at omap0: control module, rev 1.0
intc0 at omap0 rev 5.0
omap0: device edma unit 0 not configured
dmtimer0 at omap0 rev 3.1
dmtimer1 at omap0 rev 3.1
omdog0 at omap0 rev 0.1
omgpio0 at omap0: rev 0.1
omgpio1 at omap0: rev 0.1
omgpio2 at omap0: rev 0.1
omgpio3 at omap0: rev 0.1
ommmc0 at omap0
sdmmc0 at ommmc0
ommmc1 at omap0
sdmmc1 at ommmc1
com0 at omap0: ti16750, 64 byte fifo
com0: console
cpsw0 at omap0: version 1.12 (0), address 90:59:af:82:2e:7e
ukphy0 at cpsw0 phy 2: Generic IEEE 802.3u media interface, rev. 1: OUI 0x0001f0, model 0x000f
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, Drive #01, > SCSI2 0/direct fixed
sd0: 16000MB, 512 bytes/sector, 32768000 sectors
scsibus1 at sdmmc1: 2 targets, initiator 0
sd1 at scsibus1 targ 1 lun 0: <SD/MMC, Drive #01, > SCSI2 0/direct fixed
sd1: 1832MB, 512 bytes/sector, 3751936 sectors
boot device: sd0
root on rd0a swap on rd0b dump on rd0b
WARNING: CHECK AND RESET THE DATE!
erase ^?, werase ^W, kill ^U, intr ^C, status ^T
Welcome to the OpenBSD/armv7 5.5 installation program.
(I)nstall, (U)pgrade, (A)utoinstall or (S)hell? I
At any prompt except password prompts you can escape to a shell by
typing '!'. Default answers are shown in []'s and are selected by
pressing RETURN. You can exit this program at any time by pressing
Control-C, but this can leave your system in an inconsistent state.
Terminal type? [vt220]
System hostname? (short form, e.g. 'foo') beagle
Available network interfaces are: cpsw0.
Which network interface do you wish to configure? (or 'done') [cpsw0]
IPv4 address for cpsw0? (or 'dhcp' or 'none') [dhcp]
Issuing hostname-associated DHCP request for cpsw0.
DHCPDISCOVER on cpsw0 to 255.255.255.255 port 67 interval 1
DHCPOFFER from 192.168.111.1 (00:0d:b9:12:9f:2d)
DHCPREQUEST on cpsw0 to 255.255.255.255 port 67
DHCPACK from 192.168.111.1 (00:0d:b9:12:9f:2d)
bound to 192.168.111.11 -- renewal in 21600 seconds.
IPv6 address for cpsw0? (or 'rtsol' or 'none') [none]
Available network interfaces are: cpsw0.
Which network interface do you wish to configure? (or 'done') [done]
Using DNS domainname stare.cz
Using DNS nameservers at 192.168.111.1 192.168.167.254 172.17.251.254
Password for root account? (will not echo)
Password for root account? (again)
Start sshd(8) by default? [yes]
Start ntpd(8) by default? [no] yes
NTP server? (hostname or 'default') [default]
Setup a user? (enter a lower-case loginname, or 'no') [no]
What timezone are you in? ('?' for list) [Europe/Prague]
Available disks are: sd0 sd1.
Which disk is the root disk? ('?' for details) [sd0] ?
sd0: Drive #01 (15.6G)
sd1: Drive #01 (1.8G)
Available disks are: sd0 sd1.
Which disk is the root disk? ('?' for details) [sd0] sd0
Use DUIDs rather than device names in fstab? [yes]
Disk: sd0 geometry: 2039/255/63 [32768000 Sectors]
Offset: 0 Signature: 0xAA55
Starting Ending LBA Info:
#: id C H S - C H S [ start: size ]
-------------------------------------------------------------------------------
*0: 0C 0 1 1 - 1 254 63 [ 63: 32067 ] Win95 FAT32L
1: 00 0 0 0 - 0 0 0 [ 0: 0 ] unused
2: 00 0 0 0 - 0 0 0 [ 0: 0 ] unused
3: A6 0 1 2 - 1 254 63 [ 64: 32066 ] OpenBSD
Use (W)hole disk or (E)dit the MBR? [whole]
Creating a msdos partition and an OpenBSD partition for rest of sd0...done.
/dev/rsd0i: 32668 sectors in 8167 FAT16 clusters (2048 bytes/cluster)
bps=512 spc=4 res=1 nft=2 rde=512 sec=32768 mid=0xf8 spf=32 spt=63 hds=255 hid=64
The auto-allocated layout for sd0 is:
# size offset fstype [fsize bsize cpg]
a: 520.8M 32832 4.2BSD 2048 16384 1 # /
b: 768.0M 1099424 swap
c: 16000.0M 0 unused
d: 825.3M 2672288 4.2BSD 2048 16384 1 # /tmp
e: 1226.1M 4362432 4.2BSD 2048 16384 1 # /var
f: 1340.8M 6873408 4.2BSD 2048 16384 1 # /usr
g: 776.5M 9619360 4.2BSD 2048 16384 1 # /usr/X11R6
h: 2929.6M 11209568 4.2BSD 2048 16384 1 # /usr/local
i: 16.0M 64 MSDOS
j: 1200.3M 17209376 4.2BSD 2048 16384 1 # /usr/src
k: 1652.6M 19667616 4.2BSD 2048 16384 1 # /usr/obj
l: 4744.0M 23052192 4.2BSD 2048 16384 1 # /home
Use (A)uto layout, (E)dit auto layout, or create (C)ustom layout? [a]
newfs: reduced number of fragments per cylinder group from 66656 to 66392 to enlarge last cylinder group
/dev/rsd0a: 520.8MB in 1066592 sectors of 512 bytes
5 cylinder groups of 129.67MB, 8299 blocks, 16640 inodes each
/dev/rsd0l: 4744.0MB in 9715680 sectors of 512 bytes
24 cylinder groups of 202.47MB, 12958 blocks, 25984 inodes each
/dev/rsd0d: 825.3MB in 1690144 sectors of 512 bytes
5 cylinder groups of 202.47MB, 12958 blocks, 25984 inodes each
/dev/rsd0f: 1340.8MB in 2745952 sectors of 512 bytes
7 cylinder groups of 202.47MB, 12958 blocks, 25984 inodes each
newfs: reduced number of fragments per cylinder group from 99384 to 98992 to enlarge last cylinder group
/dev/rsd0g: 776.5MB in 1590208 sectors of 512 bytes
5 cylinder groups of 193.34MB, 12374 blocks, 24832 inodes each
newfs: wtfs: write error on block 5999807: Input/output error
newfs: 2bff1ccc979bfb19.k: No such file or directory
newfs: 2bff1ccc979bfb19.j: No such file or directory
newfs: 2bff1ccc979bfb19.e: No such file or directory
Available disks are: sd1.
Which disk do you wish to initialize? (or 'done') [done]
mount_ffs: 2bff1ccc979bfb19.a on /mnt: No such file or directory
mount_ffs: 2bff1ccc979bfb19.l on /mnt/home: No such file or directory
mount_ffs: 2bff1ccc979bfb19.d on /mnt/tmp: No such file or directory
mount_ffs: 2bff1ccc979bfb19.f on /mnt/usr: No such file or directory
mount_ffs: 2bff1ccc979bfb19.g on /mnt/usr/X11R6: No such file or directory
mount_ffs: 2bff1ccc979bfb19.h on /mnt/usr/local: No such file or directory
mount_ffs: 2bff1ccc979bfb19.k on /mnt/usr/obj: No such file or directory
mount_ffs: 2bff1ccc979bfb19.j on /mnt/usr/src: No such file or directory
mount_ffs: 2bff1ccc979bfb19.e on /mnt/var: No such file or directory
WARNING! The following filesystems were not properly mounted:
/mnt (2bff1ccc979bfb19.a)
/mnt/home (2bff1ccc979bfb19.l)
/mnt/tmp (2bff1ccc979bfb19.d)
/mnt/usr (2bff1ccc979bfb19.f)
/mnt/usr/X11R6 (2bff1ccc979bfb19.g)
/mnt/usr/local (2bff1ccc979bfb19.h)
/mnt/usr/obj (2bff1ccc979bfb19.k)
/mnt/usr/src (2bff1ccc979bfb19.j)
/mnt/var (2bff1ccc979bfb19.e)
Continue anyway? [no]
[prev in list] [next in list] [prev in thread] [next in thread]
Configure |
About |
News |
Add a list |
Sponsored by KoreLogic