[prev in list] [next in list] [prev in thread] [next in thread] 

List:       openbsd-arm
Subject:    "usbf_open_pipe failed" on Zaurus
From:       marius <anarcap () gmail ! com>
Date:       2008-07-04 18:38:29
Message-ID: 22318ee50807041138w22080bfbvfb0df6715de2a5b0 () mail ! gmail ! com
[Download RAW message or body]

Booting the July 2 4.4-beta bsd kernel I get the following:

usbf0 at pxaudc0: USB revision 1.1
cdcef0 at usbf0: usbf_open_pipe failed

Booting the bsd.rd kernel, the dmesg shows the following line:
cdcef0 at usbf0: address 2a:cb:00:00:00:00

I am able to configure the interface in the ramdisk kernel, but not in
generic (interface does not show up in ifconfig).

This is on a Zaurus 3200. Full dmesg below.

Thanks, Marius

OpenBSD 4.4-beta (GENERIC) #232: Wed Jul  2 12:31:55 MDT 2008
    deraadt@zaurus.openbsd.org:/usr/src/sys/arch/zaurus/compile/GENERIC
real mem  = 67108864 (64MB)
avail mem = 56643584 (54MB)
mainbus0 at root
cpu0 at mainbus0: PXA27x step C-5 (XScale core)
cpu0: DC enabled IC enabled WB enabled LABT branch prediction enabled
cpu0: 32KB(32b/l,32way) I-cache, 32KB(32b/l,32way) wr-back-lock D-cache
pxaip0 at mainbus0: CPU clock = 416.000 MHz
pxaintc0 at pxaip0 addr 0x40d00000: Interrupt Controller
pxagpio0 at pxaip0 addr 0x40e00000: GPIO Controller
pxadmac0 at pxaip0 addr 0x40000000 intr 25: DMA Controller
pxaost0 at pxaip0 addr 0x40a00000
com0 at pxaip0 addr 0x40100000 intr 22: pxa2x0, 32 byte fifo
com1 at pxaip0 addr 0x40200000 intr 21: pxa2x0, 32 byte fifo
com2 at pxaip0 addr 0x40700000 intr 20: pxa2x0, 32 byte fifo (SIR)
pxaudc0 at pxaip0: USB Device Controller
usbf0 at pxaudc0: USB revision 1.1
cdcef0 at usbf0: usbf_open_pipe failed
ohci0 at pxaip0, version 1.0
usb0 at ohci0: USB revision 1.0
uhub0 at usb0 "PXA27x OHCI root hub" rev 1.00/1.00 addr 1
lcd0 at pxaip0
wsdisplay0 at lcd0 mux 1: console (std, vt100 emulation)
wsdisplay0: screen 1 added (std, vt100 emulation)
zkbd0 at pxaip0
wskbd0 at zkbd0: console keyboard, using wsdisplay0
scoop0 at pxaip0: PCMCIA/GPIO controller
scoop1 at pxaip0: PCMCIA/GPIO controller
pxapcic0 at pxaip0: 2 slots
pcmcia0 at pxapcic0
pcmcia1 at pxapcic0
pxammc0 at pxaip0: MMC/SD/SDIO controller
sdmmc0 at pxammc0
zssp0 at pxaip0
apm0 at pxaip0
zts0 at pxaip0
wsmouse0 at zts0 mux 0
zaudio0 at pxaip0: I2C, I2S, WM8750 Audio
audio0 at zaudio0
zrc0 at pxaip0: CE-RH2 remote control
wskbd1 at zrc0 mux 1
wskbd1: connecting to wsdisplay0
flash0 at pxaip0: Samsung K9F1G08U0A 128Mx8 3.3V
wdc0 at pcmcia0 function 0 "HITACHI, microdrive" port 0x0/16: irq 138
wd0 at wdc0 channel 0 drive 0: <HMS360606D5CF00>
wd0: 32-sector PIO, LBA, 5859MB, 12000556 sectors
wd0(wdc0:0:0): using BIOS timings
softraid0 at root
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, Drive #01, > SCSI2 0/direct fixed
sd0: 972MB, 123 cyl, 255 head, 63 sec, 512 bytes/sec, 1990656 sec total
pxammc0: unhandled interrupt 2<PRGDONE>
boot device: wd0
root on wd0a swap on wd0b dump on wd0b

[prev in list] [next in list] [prev in thread] [next in thread]