[prev in list] [next in list] [prev in thread] [next in thread]
List: linux-wlan-user
Subject: [lwlan-user] WUSB11 with linux-wlan-ng 0.1.14-pre4/RH7.3; still not working
From: Ricky Ng-Adam <rngadam () yahoo ! com>
Date: 2002-05-30 3:00:27
[Download RAW message or body]
Hello!
WUSB11+linux-wlan-ng is still crashing/not working when booting with
pre4, but seems to work OK when connecting/disconnecting after boot.
HOWEVER, there seems to be a workaround (I'll have to do more
testing...) if I put a non-existing usb controller driver in
/etc/modules.conf (so that it doesn't load at start) and then do it
manually such as:
[root@localhost root]# modprobe usb-uhci
usb-uhci.c: Detected 2 ports
[root@localhost root]# lsmod
Module Size Used by Not tainted
usb-uhci 24484 0 (unused)
autofs 12164 0 (autoclean) (unused)
ds 8608 2
yenta_socket 12384 2
pcmcia_core 50752 0 [ds yenta_socket]
prism2_usb 97736 0 (unused)
p80211 23400 1 [prism2_usb]
eepro100 20336 1
ipchains 43560 12
ide-cd 30272 0 (autoclean)
cdrom 32192 0 (autoclean) [ide-cd]
usbcore 73152 1 [usb-uhci prism2_usb]
ext3 67136 1
jbd 49400 1 [ext3]
[root@localhost root]# /etc/init.d/wlan start
Starting WLAN Devices:IBSS mode started.
[root@localhost root]# ifconfig wlan0 192.168.0.11
hfa384x_drvr_setconfig: Called from within soft interrupt context.
hfa384x_drvr_setconfig: Called from within soft interrupt context.
[root@localhost root]# ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:03:47:74:19:07
inet addr:142.137.27.245 Bcast:142.137.27.255
Mask:255.255.255.0
UP BROADCAST NOTRAILERS RUNNING MULTICAST MTU:1500 Metric:1
RX packets:368 errors:0 dropped:0 overruns:0 frame:0
TX packets:5 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:177792 (173.6 Kb) TX bytes:866 (866.0 b)
Interrupt:11
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:6 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:588 (588.0 b) TX bytes:588 (588.0 b)
wlan0 Link encap:Ethernet HWaddr 00:06:25:00:E2:97
inet addr:192.168.0.11 Bcast:192.168.0.255
Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Here's the info I gathered:
=========GENERAL
Computer: IBM A22M Notebook (no, this is not the embedded computer that
will go in the submarine ;-) )
RedHat 7.3 (kernel 2.4.18-3)
=========WHEN BOOTING WITH DO_RESET=1
Unable to handle kernel paging request at virtual address 6863b*pde =
00000000
Oops: 0000
prism2_usb p80211 eepro100 ipchains ide-cd cdrom usb-uhci usbcore ext3
jbd
CPU: 0
EIP: 0010:[<c01320b2>] Not tainted
EFLAGS: 00010202
EIP is at __free_pages [kernel] 0x2 (2.4.18-3)
eax: 68637573 ebx: 00000001 ecx: 68637573 edx: 00000000
esi: cafea5c0 edi: 00000000 ebp: bffffd10 esp: cbde9e8c
ds: 0018 es: 0018 ss: 0018
Process minilogd (pid: 186, stackpage=cbde9000)
Stack: c01c5d4e cafea5c0 cbf07560 c01c5d9b cafea5c0 cbcb20e0 c01c5f18
cafea5c0
caff28a4 c01c7c8d cafea5c0 caff28a4 bffffd10 c02069fe cbf07560
c0206a1d
cbf07560 cafea5c0 ffffffea caff28a4 cbdfcf04 cbde9ef8 c01c35b3
cbdfcf04
Call Trace: [<c01c5d4e>] skb_release_data [kernel] 0x3e
[<c01c5d9b>] kfree_skbmem [kernel] 0xb
[<c01c5f18>] __kfree_skb [kernel] 0x128
[<c01c7c8d>] skb_free_datagram [kernel] 0x1d
[<c02069fe>] unix_accept [kernel] 0x4e
[<c0206a1d>] unix_accept [kernel] 0x6d
[<c01c35b3>] sys_accept [kernel] 0x63
[<c01143aa>] do_page_fault [kernel] 0x12a
[<c0127f99>] do_brk [kernel] 0x249
[<c0146c04>] poll_freewait [kernel] 0x44
[<c01c4000>] sys_socketcall [kernel] 0xb0
[<c0114280>] do_page_fault [kernel] 0x0
[<c0108a14>] error_code [kernel] 0x34
[<c0108923>] system_call [kernel] 0x33
Code: 8b 41 18 a9 00 40 00 00 75 14 ff 49 14 0f 94 c0 84 c0 74 0a
<1>Unable to handle kernel NULL pointer dereference at virtual address
000000a7 printing eip:
c012e94b
*pde = 00000000
Oops: 0002
prism2_usb p80211 eepro100 ipchains ide-cd cdrom usb-uhci usbcore ext3
jbd
CPU: 0
EIP: 0010:[<c012e94b>] Not tainted
EFLAGS: 00010056
EIP is at kmalloc [kernel] 0xcb (2.4.18-3)
eax: 00040001 ebx: cbfc05e0 ecx: cb80d380 edx: 000000a3
esi: 00000246 edi: cb047800 ebp: cb047000 esp: cb3efec0
ds: 0018 es: 0018 ss: 0018
Process initlog (pid: 744, stackpage=cb3ef000)
Stack: cb80d3e0 cbfc3005 cbfc3005 cbce9ae0 cb07f600 00000020 cb00d160
000002cc
c01c5bc0 0000065c 00000020 cb00d164 000000cc cc8a2c62 00000620
00000020
00000033 c0129a95 cba72b80 00000292 00000001 cb07f900 00000034
000000cc
Call Trace: [<c01c5bc0>] alloc_skb [kernel] 0xe0
[<cc8a2c62>] speedo_refill_rx_buf [eepro100] 0x42
[<c0129a95>] do_generic_file_read [kernel] 0x4f5
[<cc8a314c>] speedo_rx [eepro100] 0x2ec
[<c0129dee>] generic_file_read [kernel] 0x7e
[<cc8a2b0b>] speedo_interrupt [eepro100] 0xab
[<c0109c7a>] handle_IRQ_event [kernel] 0x3a
[<c0109df8>] do_IRQ [kernel] 0x68
Code: 89 42 04 89 10 8b 03 89 48 04 89 01 89 59 04 89 0b 56 9d 89
<0>Kernel panic: Aiee, killing interrupt handler!
In interrupt handler - not syncing
============WHEN BOOTING WITH DO_RESET=0
[root@localhost root]# ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:03:47:74:19:07
inet addr:142.137.27.245 Bcast:142.137.27.255
Mask:255.255.255.0
UP BROADCAST NOTRAILERS RUNNING MULTICAST MTU:1500 Metric:1
RX packets:122 errors:0 dropped:0 overruns:0 frame:0
TX packets:5 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:54566 (53.2 Kb) TX bytes:866 (866.0 b)
Interrupt:11 Base address:0x7000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:6 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:588 (588.0 b) TX bytes:588 (588.0 b)
wlan0 Link encap:Ethernet HWaddr 00:00:00:00:00:00
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
[root@localhost root]# /etc/init.d/wlan start
Starting WLAN Devices:hfa384x_docmd: hfa384x_docmd:ctlx
failure=REQ_TIMEOUT
hfa384x_drvr_start: hfa384x_drvr_startcmd_initialize() failed,
result=-5
prism2sta_ifstate: hfa384x_drvr_start() failed,result=-5
Failed to enable the device, resultcode= implementation_failure .
[root@localhost root]# modprobe -r prism2_usb
prism2_usb.o: 0.1.14-pre4 Unloaded
p80211.o: 0.1.14-pre4 Unloaded
[root@localhost root]# modprobe prism2_usb prism2_doreset=1
init_module: prism2_usb.o: 0.1.14-pre4 Loaded
init_module: dev_info is: prism2_usb
[root@localhost root]# usb.c: unexpected descriptor 0x0, expecting
endpoint des5usb.c: unexpected descriptor 0x0, expecting endpoint
descriptor, type 0x5
usb.c: unexpected descriptor 0x0, expecting endpoint descriptor, type
0x5
usb.c: USB device 3 (vend/prod 0x66b/0x2212) is not claimed by any
active drive.
[root@localhost root]# /etc/init.d/wlan start
Starting WLAN Devices:usb-uhci.c: uhci_submit_urb: pipesize for pipe
c0008380 iohfa384x_drvr_start: hfa384x_drvr_start:Fatal,
usb_submit_urb() failed, result=-0prism2sta_ifstate:
hfa384x_drvr_start() failed,result=-90
Failed to enable the device, resultcode= implementation_failure .
===========MANUALLY RECONNECTING AFTER BOOT
[root@localhost root]# lsmod
Module Size Used by Not tainted
autofs 12164 0 (autoclean) (unused)
ds 8608 2
yenta_socket 12384 2
pcmcia_core 50752 0 [ds yenta_socket]
prism2_usb 97736 0 (unused)
p80211 23400 1 [prism2_usb]
eepro100 20336 1
ipchains 43560 12
ide-cd 30272 0 (autoclean)
cdrom 32192 0 (autoclean) [ide-cd]
usb-uhci 24484 0 (unused)
usbcore 73152 1 [prism2_usb usb-uhci]
ext3 67136 1
jbd 49400 1 [ext3]
[root@localhost root]# /etc/init.d/wlan start
Starting WLAN Devices:IBSS mode started.
[root@localhost root]# ifconfig wlan0 192.168.0.11
hfa384x_drvr_setconfig: Called from within soft interrupt context.
hfa384x_drvr_setconfig: Called from within soft interrupt context.
hfa384x_drvr_setconfig: Called from within soft interrupt context.
wlan0 Link encap:Ethernet HWaddr 00:06:25:00:E2:97
inet addr:192.168.0.11 Bcast:192.168.0.255
Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
===================================/etc/modules.conf
options prism2_usb prism2_doreset=1 prism2_debug=3
alias wlan0 prism2_usb
options p80211 wlan_debug=2
(also tried prism2_doreset=0)
===================================DMESG
[root@localhost root]# dmesg
Linux version 2.4.18-3 (bhcompile@daffy.perf.redhat.com) (gcc version
2.96 20002BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000bff0000 (usable)
BIOS-e820: 000000000bff0000 - 000000000bffec00 (ACPI data)
BIOS-e820: 000000000bffec00 - 000000000c000000 (ACPI NVS)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
On node 0 totalpages: 49136
zone(0): 4096 pages.
zone(1): 45040 pages.
zone(2): 0 pages.
IBM machine detected. Enabling interrupts during APM calls.
Kernel command line: ro root=/dev/hda6 console=ttyS0,9600n8
console=tty0
Initializing CPU#0
Detected 797.047 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1592.52 BogoMIPS
Memory: 190804k/196544k available (1119k kernel code, 5352k reserved,
775k data)Dentry cache hash table entries: 32768 (order: 6, 262144
bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
Buffer cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: Before vendor init, caps: 0383f9ff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After vendor init, caps: 0383f9ff 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383f9ff 00000000 00000000 00000000
CPU: Common caps: 0383f9ff 00000000 00000000 00000000
CPU: Intel Pentium III (Coppermine) stepping 0a
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfd94f, last bus=7
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 2: assuming transparent
PCI: Discovered primary peer bus 08 [IRQ]
PCI: Using IRQ router PIIX [8086/7110] at 00:07.0
Limiting direct PCI/PCI transfers.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Starting kswapd
VFS: Diskquotas version dquot_6.5.0 initialized
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT
SHARE_IRQ SEdttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
PCI: Found IRQ 11 for device 00:03.1
PCI: Sharing IRQ 11 with 00:03.0
Redundant entry in serial pci_table. Please send the output of
lspci -vv, this message (11c1,045c,8086,2205)
and the manufacturer and name of serial board or modem board
to serial-pci-info@lists.sourceforge.net.
register_serial(): autoconfig failed
Real Time Clock Driver v1.10e
block: 368 slots per queue, batch=92
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1850-0x1857, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1858-0x185f, BIOS settings: hdc:DMA, hdd:pio
hda: IBM-DJSA-210, ATA DISK drive
hdc: CD-224E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
blk: queue c035e6a4, I/O limit 4095Mb (mask 0xffffffff)
hda: 19640880 sectors (10056 MB) w/384KiB Cache, CHS=1299/240/63,
UDMA(33)
ide-floppy driver 0.99.newide
Partition check:
hda: hda1 hda2 < hda5 hda6 hda7 >
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 120k freed
VFS: Mounted root (ext2 filesystem).
Journalled Block Device driver loaded
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: ide0(3,6): orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 260044
ext3_orphan_cleanup: deleting unreferenced inode 260043
EXT3-fs: ide0(3,6): 2 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 280k freed
Adding Swap: 249440k swap-space (priority -1)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 07:43:07 Apr 18 2002
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 11 for device 00:07.2
usb-uhci.c: USB UHCI at I/O 0x1860, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
hub.c: USB new device connect on bus1/1, assigned device number 2
usb.c: USB device descriptor short read (expected 18, got 8)
hub.c: USB new device connect on bus1/1, assigned device number 3
usb.c: USB device descriptor short read (expected 18, got 16)
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,6), internal journal
ide-floppy driver 0.99.newide
hdc: ATAPI 24X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
hdc: DMA disabled
parport0: PC-style at 0x3bc [PCSPP,TRISTATE]
ip_conntrack (1535 buckets, 12280 max)
eepro100.c:v1.09j-t 9/29/99 Donald Becker
http://www.scyld.com/network/eepro100leepro100.c: $Revision: 1.36 $
2000/11/17 Modified by Andrey V. Savochkin <saw@ssPCI: Found IRQ 11 for
device 00:03.0
PCI: Sharing IRQ 11 with 00:03.1
eth0: OEM i82557/i82558 10/100 Ethernet, 00:03:47:74:19:07, IRQ 11.
Board assembly a30469-007, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
Secondary interface chip i82555.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x3258698e).
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
PCI: Found IRQ 11 for device 00:02.0
PCI: Sharing IRQ 11 with 00:05.0
PCI: Sharing IRQ 11 with 01:00.0
PCI: Found IRQ 11 for device 00:02.1
Yenta IRQ list 06b8, PCI irq11
Socket status: 30000006
Yenta IRQ list 06b8, PCI irq11
Socket status: 30000006
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x3b8-0x3df 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
[root@localhost root]# lspci -vv
00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host
bridge (rev 0) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV-
VGASnoop- ParErr- Ste- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr-
DEVSEL=medium >TAbort- <TAbor- Latency: 64
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 1.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge
(rev 03)) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+
VGASnoop- ParErr- Ste- Status: Cap- 66Mhz+ UDF- FastB2B- ParErr-
DEVSEL=medium >TAbort- <TAbor- Latency: 128
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f4200000-f5ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B+
00:02.0 CardBus bridge: Texas Instruments PCI1450 (rev 03)
Subsystem: IBM: Unknown device 0130
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Ste- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr-
DEVSEL=medium >TAbort- <TAbor- Latency: 168, cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 50000000 (32-bit, non-prefetchable)
[size=4K]
Bus: primary=00, secondary=02, subordinate=04, sec-latency=176
Memory window 0: 10000000-103ff000 (prefetchable)
Memory window 1: 10400000-107ff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+
PostWrite+
16-bit legacy interface ports at 0001
00:02.1 CardBus bridge: Texas Instruments PCI1450 (rev 03)
Subsystem: IBM: Unknown device 0130
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Ste- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr-
DEVSEL=medium >TAbort- <TAbor- Latency: 168, cache line size 08
Interrupt: pin B routed to IRQ 11
Region 0: Memory at 50100000 (32-bit, non-prefetchable)
[size=4K]
Bus: primary=00, secondary=05, subordinate=07, sec-latency=176
Memory window 0: 10800000-10bff000 (prefetchable)
Memory window 1: 10c00000-10fff000
I/O window 0: 00004800-000048ff
I/O window 1: 00004c00-00004cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+
PostWrite+
16-bit legacy interface ports at 0001
00:03.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100]
(rev 0c)
Subsystem: Intel Corp. EtherExpress PRO/100 SP Mobile Combo
Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Ste- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbor- Latency: 66 (2000ns min, 14000ns
max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f4120000 (32-bit, non-prefetchable)
[size=4K]
Region 1: I/O ports at 1800 [size=64]
Region 2: Memory at f4100000 (32-bit, non-prefetchable)
[size=128K]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3ho) Status: D0 PME-Enable- DSel=0
DScale=2 PME-
00:03.1 Serial controller: Lucent Microelectronics: Unknown device 045c
(rev 01) Subsystem: Intel Corp.: Unknown device 2205
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Ste- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr-
DEVSEL=medium >TAbort- <TAbor- Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 1840 [size=8]
Region 1: Memory at f4121000 (32-bit, non-prefetchable)
[size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3ho) Status: D0 PME-Enable- DSel=0
DScale=2 PME-
00:05.0 Multimedia audio controller: Cirrus Logic CS 4614/22/24
[CrystalClear S) Subsystem: IBM: Unknown device 0153
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Ste- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr-
DEVSEL=slow >TAbort- <TAbort-- Interrupt: pin A routed to IRQ 11
Region 0: Memory at f4122000 (32-bit, non-prefetchable)
[size=4K]
Region 1: Memory at f4000000 (32-bit, non-prefetchable)
[size=1M]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3ho) Status: D0 PME-Enable- DSel=0
DScale=0 PME-
00:07.0 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Ste- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbor- Latency: 0
00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01)
(prog-if 80) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV-
VGASnoop- ParErr- Ste- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbor- Latency: 64
Region 4: I/O ports at 1850 [size=16]
00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01)
(prog-if 0) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV-
VGASnoop- ParErr- Ste- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbor- Latency: 64
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at 1860 [size=32]
00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 03)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Ste- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbor- Interrupt: pin ? routed to IRQ 9
01:00.0 VGA compatible controller: ATI Technologies Inc Rage Mobility
P/M AGP 2) Subsystem: IBM: Unknown device 0154
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Ste- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbor- Latency: 66 (2000ns min), cache
line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f5000000 (32-bit, non-prefetchable)
[size=16M]
Region 1: I/O ports at 2000 [size=256]
Region 2: Memory at f4200000 (32-bit, non-prefetchable)
[size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [50] AGP version 1.0
Status: RQ=255 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [5c] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3ho) Status: D0 PME-Enable- DSel=0
DScale=0 PME-
=========================
Thanks!
=====
Ricky Ng-Adam, responsable logiciel du projet SONIA de l'ÉTS
http://sonia.etsmtl.ca, http://bigbrainbox.com, http://race.etsmtl.ca
__________________________________________________
Do You Yahoo!?
Yahoo! - Official partner of 2002 FIFA World Cup
http://fifaworldcup.yahoo.com
[prev in list] [next in list] [prev in thread] [next in thread]
Configure |
About |
News |
Add a list |
Sponsored by KoreLogic