[prev in list] [next in list] [prev in thread] [next in thread]
List: linux-wlan-devel
Subject: [lwlan-devel] Compaq WL100 "GetNextTuple" ... Vcc? failure..?
From: linux-wlan-devel () lists ! linux-wlan ! com (Kai Gossens)
Date: 2001-08-20 17:13:59
[Download RAW message or body]
Hello,
i have a Compaq WL100 card (Firmware 0.8), a linux-PC with an ISA
PCMCIA Adapter.
Im using Redhat 7.x, linux-wlan 0.1.8pre13 (same problem with 0.1.7) drivers
and the pcmcia-cs-3.1.28 package.
Problem:
I start the pcmcia device with /etc/rc.d/init.d/pcmcia start and i get a high
beep follow by an low beep. My logfile shows the lines below..
Aug 19 16:13:15 miraculix cardmgr[2971]: socket 0: Compaq WL100/200 11Mb/s 802.11b \
WLAN Card
Aug 19 16:13:15 miraculix cardmgr[2971]: executing: 'modprobe prism2_cs'
Aug 19 16:13:15 miraculix kernel: init_module: prism2_cs.o: 0.1.8-pre13 Loaded
Aug 19 16:13:15 miraculix kernel: init_module: dev_info is: prism2_cs
Aug 19 16:13:15 miraculix kernel: prism2_cs: GetNextTuple: No more items
Aug 19 16:13:15 miraculix kernel: prism2sta_config: NextTuple failure? It's probably \
a Vcc mismatch.
Aug 19 16:13:15 miraculix kernel: prism2sta_event: prism2_cs: Initialization failed!
Aug 19 16:13:16 miraculix cardmgr[2971]: get dev info on socket 0 failed: Resource \
temporarily unavailable
A dump with dump_cis -v shows the lines below.....
Socket 0:
offset 0x02, tuple 0x01, link 0x03
00 00 ff
dev_info
NULL 0ns, 512b
offset 0x07, tuple 0x17, link 0x04
67 5a 08 ff
attr_dev_info
SRAM 500ns, 1kb
offset 0x0d, tuple 0x1d, link 0x05
03 67 5a 08 ff
offset 0x14, tuple 0x15, link 0x50
05 00 43 6f 6d 70 61 71 00 57 4c 31 30 30 5f 31
31 4d 62 70 73 5f 57 69 72 65 6c 65 73 73 5f 50
43 5f 43 61 72 64 00 56 65 72 73 69 6f 6e 20 30
31 2e 30 30 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ff
vers_1 5.0, "Compaq", "WL100_11Mbps_Wireless_PC_Card", "Version 01.00",
""
offset 0x66, tuple 0x20, link 0x04
38 01 02 00
manfid 0x0138, 0x0002
offset 0x6c, tuple 0x21, link 0x02
06 00
funcid network_adapter
offset 0x70, tuple 0x22, link 0x02
01 07
lan_technology wireless
offset 0x74, tuple 0x22, link 0x05
02 40 42 0f 00
lan_speed 1 mb/sec
offset 0x7b, tuple 0x22, link 0x05
02 80 84 1e 00
lan_speed 2 mb/sec
offset 0x82, tuple 0x22, link 0x05
02 60 ec 53 00
lan_speed 5 mb/sec
offset 0x89, tuple 0x22, link 0x05
02 c0 d8 a7 00
lan_speed 11 mb/sec
offset 0x90, tuple 0x22, link 0x02
03 07
lan_media 2.4_GHz
offset 0x94, tuple 0x22, link 0x08
04 06 00 20 ca 00 13 19
lan_node_id 00 20 ca 00 13 19
offset 0x9e, tuple 0x22, link 0x02
05 01
lan_connector Closed connector standard
offset 0xa2, tuple 0x1a, link 0x07
03 01 e0 03 00 00 01
config base 0x03e0 mask 0x0001 last_index 0x01
offset 0xab, tuple 0x1b, link 0x10
c1 01 19 77 b5 1e 35 b5 3c 36 36 05 46 7f ff ff
cftable_entry 0x01 [default]
Vcc Vnom 3300mV Vmin 3V Vmax 3600mV Iavg 300mA
Ipeak 300mA Idown 10mA
io 0x0000-0x003f [lines=6] [16bit]
irq mask 0xffff [level] [pulse]
Can anyone help me?
With kind regards
Kai
[prev in list] [next in list] [prev in thread] [next in thread]
Configure |
About |
News |
Add a list |
Sponsored by KoreLogic