[prev in list] [next in list] [prev in thread] [next in thread]
List: linux-vlan
Subject: [VLAN] Re: URGENT my friend : How to startup the VLAN?
From: <eg_wcw () yahoo ! com>
Date: 2001-12-27 5:56:58
[Download RAW message or body]
Here is the result after I typed
"./vconfig add eth1 5"
However, I cannot do the "ifconfig -i eth1.5
192.168.2.1"
There is an error "ifconfig: unknown option -i
(Use --help for usage information.)"
Any other command can replace the -i parameter?
Like "ifconfig add"??
Please help to verify my setting. Is it wrong when I
install the patch???
eth0 Link encap:Ethernet HWaddr
00:02:B3:86:1D:1A
inet addr:192.168.1.69 Bcast:192.168.1.255
Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500
Metric:1
RX packets:91512 errors:0 dropped:0
overruns:0 frame:0
TX packets:38849 errors:0 dropped:0
overruns:0 carrier:0
collisions:0 txqueuelen:100
Interrupt:5 Base address:0xef00
Memory:d0836000-d0836c40
eth1 Link encap:Ethernet HWaddr
00:02:B3:86:1D:1B
inet addr:192.168.1.69 Bcast:192.168.1.255
Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500
Metric:1
RX packets:50350 errors:1 dropped:0
overruns:0 frame:1
TX packets:31389 errors:33 dropped:0
overruns:0 carrier:33
collisions:504 txqueuelen:100
Interrupt:5 Base address:0xee80
Memory:d0838000-d0838c40
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:3924 Metric:1
RX packets:2188 errors:0 dropped:0
overruns:0 frame:0
TX packets:2188 errors:0 dropped:0
overruns:0 carrier:0
collisions:0 txqueuelen:0
vlan0005 Link encap:Ethernet HWaddr
00:02:B3:86:1D:1B
BROADCAST RUNNING MULTICAST MTU:1500
Metric:1
RX packets:0 errors:0 dropped:0 overruns:0
frame:0
TX packets:0 errors:0 dropped:0 overruns:0
carrier:0
collisions:0 txqueuelen:
--- Ben Greear <greearb@candelatech.com>
的郵件內容:> Please send this message to the VLAN
mailing list
> instead of
> directly to me.
>
> To better debug, send us output of:
> ifconfig -a
> after you do the vconfig add eth1 5
>
> Most likely, you ifconfig statement should
> be:
> ifconfig -i eth1.5 192.168.2.1
>
> Note eth1 v/s eth0, because your vconfig statement
> uses eth1....
>
> Ben
>
> Leo Leo wrote:
>
> > Hi Greear!
> >
> > Thanks for you to answer my previous questions.
> > I followed the instructions to install the 802.1Q
> > patch into my existing kernel. Also, I downloaded
> > the kernel source code with the same version
> number
> > of my existing kernel to compile the "vconfig"
> > program.
> > I can see the 802.1Q wording when my machine
> bootup.
> > I can also run the vconfig program.
> > Am I got a 802.1Q capable machine?
> >
> > I can execute "vconfig add eth1 5".
> > But I am not able to execute
> > "ifconfig -i eth0.5 192.168.2.1"
> > Do you know what happens?
> >
> > Thanks my friend!
> > Please let me know coz I am in urgent!
> >
> >
> >
>
_________________________________________________________
> > Do you Yahoo!?
> > 行萬里路 http://travel.yahoo.com.hk
> > Comprehensive travel guide at
> http://travel.yahoo.com.hk
> >
> >
>
>
> --
> Ben Greear <greearb@candelatech.com>
> <Ben_Greear AT excite.com>
> President of Candela Technologies Inc
> http://www.candelatech.com
> ScryMUD: http://scry.wanfear.com
> http://scry.wanfear.com/~greear
>
>
_________________________________________________________
Do you Yahoo!?
行萬里路 http://travel.yahoo.com.hk
Comprehensive travel guide at http://travel.yahoo.com.hk
_______________________________________________
VLAN mailing list - VLAN@Scry.WANfear.com
http://www.WANfear.com/mailman/listinfo/vlan
VLAN Page: http://scry.wanfear.com/~greear/vlan.html
[prev in list] [next in list] [prev in thread] [next in thread]
Configure |
About |
News |
Add a list |
Sponsored by KoreLogic