[prev in list] [next in list] [prev in thread] [next in thread]
List: linux-smp
Subject: new IO-APIC / unexpected IO-APIC
From: Friedrich Lobenstock <fl () fl ! priv ! at>
Date: 2000-12-27 18:07:12
[Download RAW message or body]
On a new Tiger 200 MB (http://www.tyan.com/products/html/tiger200_p.html )
I get "unexpected IO-APIC" during boot.
Please CC me because I'm not on the list.
Regards
Friedrich Lobenstock
Inspecting /boot/System.map
Loaded 7153 symbols from /boot/System.map.
Symbols match kernel version 2.2.18.
Loaded 5 symbols from 1 module.
klogd 1.3-3, log source = ksyslog started.
<4>Linux version 2.2.18 (root@proxy1) (gcc version egcs-2.91.66 19990314/Linux \
(egcs-1.1.2 release)) #1 SMP Mon Dec 11 19:58:38 CET 2000 <4>Scan SMP from c0000000 \
for 1024 bytes. <4>Scan SMP from c009fc00 for 1024 bytes.
<4>Scan SMP from c00f0000 for 65536 bytes.
<4>Intel MultiProcessor Specification v1.1
<4> Virtual Wire compatibility mode.
<4>OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
<4>Processor #0 Pentium(tm) Pro APIC version 17
<4> Floating point unit present.
<4> Machine Exception supported.
<4> 64 bit compare & exchange supported.
<4> Internal APIC present.
<4> Bootup CPU
<4>Processor #1 Pentium(tm) Pro APIC version 17
<4> Floating point unit present.
<4> Machine Exception supported.
<4> 64 bit compare & exchange supported.
<4> Internal APIC present.
<4>Bus #0 is PCI
<4>Bus #1 is PCI
<4>Bus #2 is ISA
<4>I/O APIC #2 Version 17 at 0xFEC00000.
<4>Processors: 2
<4>mapped APIC to ffffe000 (fee00000)
<4>mapped IOAPIC to ffffd000 (fec00000)
<4>Detected 799748 kHz processor.
<4>Console: colour VGA+ 80x25
<4>Calibrating delay loop... 1595.80 BogoMIPS
<4>Memory: 517068k/524224k available (1224k kernel code, 424k reserved, 5448k data, \
60k init) <4>Dentry hash table entries: 65536 (order 7, 512k)
<4>Buffer cache hash table entries: 524288 (order 9, 2048k)
<4>Page cache hash table entries: 131072 (order 7, 512k)
<6>CPU serial number disabled.
<4>256K L2 cache (8 way)
<4>CPU: L2 Cache: 256K
<6>Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
<6>Checking 'hlt' instruction... OK.
<4>POSIX conformance testing by UNIFIX
<4>mtrr: v1.35a (19990819) Richard Gooch (rgooch@atnf.csiro.au)
<6>CPU serial number disabled.
<6>Intel machine check architecture supported.
<6>Intel machine check reporting enabled on CPU#0.
<4>256K L2 cache (8 way)
<4>CPU: L2 Cache: 256K
<4>per-CPU timeslice cutoff: 50.04 usecs.
<4>CPU0: Intel Pentium III (Coppermine) stepping 06
<4>Getting VERSION: 40011
<4>Getting VERSION: 40011
<4>Getting LVT0: 700
<4>Getting LVT1: 400
<4>setup_APIC_clock() called.
<4>calibrating APIC timer ...
<4>..... 7997693 CPU clocks in 1 timer chip tick.
<4>..... 1332947 APIC bus clocks in 1 timer chip tick.
<4>..... CPU clock speed is 799.7693 MHz.
<4>..... system bus clock speed is 133.2947 MHz.
<4>CPU map: 3
<4>Booting processor 1 eip 2000
<4>Setting warm reset code and vector.
<4>1.
<4>2.
<4>3.
<4>Asserting INIT.
<4>Deasserting INIT.
<4>Sending STARTUP #1.
<4>After apic_write.
<4>Before start apic_write.
<4>Startup point 1.
<4>Waiting for send to finish...
<4>CPU#1 waiting for CALLOUT
<4>+Sending STARTUP #2.
<4>After apic_write.
<4>Before start apic_write.
<4>Startup point 1.
<4>Waiting for send to finish...
<4>+After Startup.
<4>Before Callout 1.
<4>After Callout 1.
<4>CALLIN, before enable_local_APIC().
<4>setup_APIC_clock() called.
<4>waiting for other CPU calibrating APIC ... done, continuing.
<4>Calibrating delay loop... 1599.07 BogoMIPS
<4>Stack at about dffebfbc
<6>CPU serial number disabled.
<6>Intel machine check reporting enabled on CPU#1.
<4>256K L2 cache (8 way)
<4>CPU: L2 Cache: 256K
<4>OK.
<4>CPU1: Intel Pentium III (Coppermine) stepping 06
<4>CPU has booted.
<4>Before bogomips.
<6>Total of 2 processors activated (3194.88 BogoMIPS).
<4>Before bogocount - setting activated=1.
<4>Boot done.
<4>enabling symmetric IO mode... ...done.
<4>ENABLING IO-APIC IRQs
<4>init IO_APIC IRQs
<4> IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not \
connected. <4>number of MP IRQ sources: 16.
<4>number of IO-APIC #2 registers: 24.
<4>testing the IO APIC.......................
<4>
<4>IO APIC #2......
<4>.... register #00: 02000000
<4>....... : physical APIC id: 02
<4>.... register #01: 00178011
<4>....... : max redirection entries: 0017
<4>....... : IO APIC version: 0011
<4> WARNING: unexpected IO-APIC, please mail
<4> to linux-smp@vger.kernel.org
<4>.... register #02: 00000000
<4>....... : arbitration: 00
<4>.... IRQ redirection table:
<4> NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
<4> 00 000 00 1 0 0 0 0 0 0 00
<4> 01 000 00 0 0 0 0 0 1 1 59
<4> 02 0FF 0F 0 0 0 0 0 1 1 51
<4> 03 000 00 0 0 0 0 0 1 1 61
<4> 04 000 00 0 0 0 0 0 1 1 69
<4> 05 0FF 0F 1 1 0 1 0 1 1 71
<4> 06 000 00 0 0 0 0 0 1 1 79
<4> 07 000 00 0 0 0 0 0 1 1 81
<4> 08 000 00 0 0 0 0 0 1 1 89
<4> 09 0FF 0F 1 1 0 1 0 1 1 91
<4> 0a 0FF 0F 1 1 0 1 0 1 1 99
<4> 0b 0FF 0F 1 1 0 1 0 1 1 A1
<4> 0c 000 00 0 0 0 0 0 1 1 A9
<4> 0d 000 00 1 0 0 0 0 0 0 00
<4> 0e 000 00 0 0 0 0 0 1 1 B1
<4> 0f 000 00 0 0 0 0 0 1 1 B9
<4> 10 000 00 1 0 0 0 0 0 0 00
<4> 11 000 00 1 0 0 0 0 0 0 00
<4> 12 000 00 1 0 0 0 0 0 0 00
<4> 13 000 00 1 0 0 0 0 0 0 00
<4> 14 000 00 1 0 0 0 0 0 0 00
<4> 15 000 00 1 0 0 0 0 0 0 00
<4> 16 000 00 1 0 0 0 0 0 0 00
<4> 17 000 00 1 0 0 0 0 0 0 00
<7>IRQ to pin mappings:
<7>IRQ0 -> 2
<7>IRQ1 -> 1
<7>IRQ3 -> 3
<7>IRQ4 -> 4
<7>IRQ5 -> 5
<7>IRQ6 -> 6
<7>IRQ7 -> 7
<7>IRQ8 -> 8
<7>IRQ9 -> 9
<7>IRQ10 -> 10
<7>IRQ11 -> 11
<7>IRQ12 -> 12
<7>IRQ13 -> 13
<7>IRQ14 -> 14
<7>IRQ15 -> 15
<4>.................................... done.
<4>checking TSC synchronization across CPUs: passed.
<4>Setting commenced=1, go go go
<4>mtrr: your CPUs had inconsistent variable MTRR settings
<4>mtrr: probably your BIOS does not setup all CPUs
<4>PCI: PCI BIOS revision 2.10 entry at 0xfb390
<4>PCI: Using configuration type 1
<4>PCI: Probing PCI hardware
<6>Linux NET4.0 for Linux 2.2
<6>Based upon Swansea University Computer Society NET3.039
<6>NET4: Unix domain sockets 1.0 for Linux NET4.0.
<6>NET4: Linux TCP/IP 1.0 for NET4.0
<6>IP Protocols: ICMP, UDP, TCP, IGMP
<4>TCP: Hash tables configured (ehash 524288 bhash 65536)
<4>Initializing RT netlink socket
<4>Starting kswapd v 1.5
<6>Detected PS/2 Mouse Port.
<6>Serial driver version 4.27 with no serial options enabled
<6>ttyS00 at 0x03f8 (irq = 4) is a 16550A
<6>ttyS01 at 0x02f8 (irq = 3) is a 16550A
<4>pty: 256 Unix98 ptys configured
<6>Real Time Clock Driver v1.09
<6>Uniform Multi-Platform E-IDE driver Revision: 6.30
<4>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
<4>VP_IDE: IDE controller on PCI bus 00 dev 39
<4>VP_IDE: chipset revision 6
<4>VP_IDE: not 100% native mode: will probe irqs later
<4> ide0: BM-DMA at 0xc400-0xc407, BIOS settings: hda:DMA, hdb:pio
<4> ide1: BM-DMA at 0xc408-0xc40f, BIOS settings: hdc:pio, hdd:pio
<4>hda: IBM-DJNA-371350, ATA DISK drive
<4>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
<6>hda: IBM-DJNA-371350, 12949MB w/1966kB Cache, CHS=1650/255/63, UDMA(33)
<6>Floppy drive(s): fd0 is 1.44M
<6>FDC 0 is a post-1991 82077
<6>(scsi0) <Adaptec AIC-7892 Ultra 160/m SCSI host adapter> found at PCI 0/19/0
<6>(scsi0) Wide Channel, SCSI ID=7, 32/255 SCBs
<6>(scsi0) Downloading sequencer code... 392 instructions downloaded
<4>scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.31/3.2.4
<4> <Adaptec AIC-7892 Ultra 160/m SCSI host adapter>
<4>scsi : 1 host.
<6>(scsi0:0:0:0) Synchronous at 40.0 Mbyte/sec, offset 31.
<4> Vendor: IBM Model: DNES-318350W Rev: SA30
<4> Type: Direct-Access ANSI SCSI revision: 03
<4>Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
<6>(scsi0:0:3:0) Synchronous at 20.0 Mbyte/sec, offset 15.
<4> Vendor: PLEXTOR Model: CD-ROM PX-40TS Rev: 1.02
<4> Type: CD-ROM ANSI SCSI revision: 02
<4>Detected scsi CD-ROM sr0 at scsi0, channel 0, id 3, lun 0
<4>scsi : detected 1 SCSI cdrom 1 SCSI disk total.
<6>Uniform CD-ROM driver Revision: 3.11
<4>SCSI device sda: hdwr sector= 512 bytes. Sectors= 35843670 [17501 MB] [17.5 GB]
<6>Partition check:
<6> sda: sda1 sda2 sda3 sda4
<6> hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
<4>VFS: Mounted root (ext2 filesystem) readonly.
<4>Freeing unused kernel memory: 60k freed
<6>Adding Swap: 265064k swap-space (priority -1)
<6>Adding Swap: 265032k swap-space (priority -2)
<6>3c59x.c 15Sep00 Donald Becker and others http://www.scyld.com/network/vortex.html
<6>eth0: 3Com 3c905C Tornado at 0xd800, 00:50:da:3c:a3:42, IRQ 9
<6> 8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
<6> MII transceiver found at address 24, status 782d.
<6> Enabling bus-master transmits and whole-frame receives.
<6>eth1: 3Com 3c905C Tornado at 0xdc00, 00:50:da:3c:3f:5a, IRQ 5
<6> 8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
<6> MII transceiver found at address 24, status 782d.
<6> Enabling bus-master transmits and whole-frame receives.
<6>eth2: 3Com 3c905C Tornado at 0xe000, 00:01:02:10:31:be, IRQ 10
<6> 8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
<6> MII transceiver found at address 24, status 782d.
<6> Enabling bus-master transmits and whole-frame receives.
Kernel logging (ksyslog) stopped.
Kernel log daemon terminating.
-
To unsubscribe from this list: send the line "unsubscribe linux-smp" in
the body of a message to majordomo@vger.kernel.org
[prev in list] [next in list] [prev in thread] [next in thread]
Configure |
About |
News |
Add a list |
Sponsored by KoreLogic