[prev in list] [next in list] [prev in thread] [next in thread]
List: linux-smp
Subject: SiS740 & IO-APIC
From: "Thomas Herrmann" <ollo.diab () gmx ! de>
Date: 2004-01-02 10:23:20
Message-ID: 30594.1073039000 () www57 ! gmx ! net
[Download RAW message or body]
Hello,
today I unstalled Linux kernel 2.4.24pre3 vanilla on my SiS740 system
(Shuttle SS40G). I enabled the IO-APIC in the BIOS (Version 1.4) and booted the
newly compiled kernel. The IO-APIC gets used, but I get a warning messing
telling me to send an email to you. So please find below the dmesg output as well
as the interrupt routing and lspci -v:
# cat /proc/interrupts
CPU0
0: 818279 IO-APIC-edge timer
1: 3 IO-APIC-edge keyboard
2: 0 XT-PIC cascade
3: 254 IO-APIC-edge serial
8: 2 IO-APIC-edge rtc
9: 8638 IO-APIC-level acpi
14: 134127 IO-APIC-edge ide0
15: 8 IO-APIC-edge ide1
17: 0 IO-APIC-level CMI8738-MC6
18: 68329 IO-APIC-level eth0
20: 8638 IO-APIC-level usb-ohci
23: 1879589 IO-APIC-level usb-ohci
NMI: 0
LOC: 818256
ERR: 0
MIS: 0
#dmesg
age 000f5000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f1000 reserved twice.
hm, page 000f2000 reserved twice.
On node 0 totalpages: 57328
zone(0): 4096 pages.
zone(1): 53232 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 AWARD ) @ 0x000f6c40
ACPI: RSDT (v001 AWARD AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0dff3000
ACPI: FADT (v001 AWARD AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0dff3040
ACPI: MADT (v001 AWARD AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0dff67c0
ACPI: DSDT (v001 AWARD AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 Pentium(tm) Pro APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0])
IOAPIC[0]: Assigned apic_id 2
IOAPIC[0]: apic_id 2, version 20, address 0xfec00000, IRQ 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 dfl dfl)
ACPI BALANCE SET
Using ACPI (MADT) for SMP configuration information
Kernel command line: root=/dev/hda3 hda=flash hdc=ide-scsi
ide_setup: hda=flash
ide_setup: hdc=ide-scsi
Initializing CPU#0
Detected 1327.714 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 2647.65 BogoMIPS
Memory: 224252k/229312k available (1358k kernel code, 4676k reserved, 470k
data, 120k init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff c1cbfbff 00000000 00000000
CPU: Common caps: 0383fbff c1cbfbff 00000000 00000000
CPU: AMD Athlon(tm) XP 1500+ stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23
not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1327.6775 MHz.
..... host bus clock speed is 265.5353 MHz.
cpu: 0, clocks: 2655353, slice: 1327676
CPU0<T0:2655344,T1:1327664,D:4,S:1327676,C:2655353>
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20031203
PCI: PCI BIOS revision 2.10 entry at 0xfb360, last bus=1
IOAPIC[0]: Set PCI routing entry (2-9 -> 0x71 -> IRQ 9 Mode:1 Active:1)
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: System [ACPI] (supports S0 S1 S3 S4 S5)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
PCI: Probing PCI hardware
IOAPIC[0]: Set PCI routing entry (2-18 -> 0xa9 -> IRQ 18 Mode:1 Active:1)
00:00:0b[A] -> 2-18 -> IRQ 18
IOAPIC[0]: Set PCI routing entry (2-19 -> 0xb1 -> IRQ 19 Mode:1 Active:1)
00:00:0b[B] -> 2-19 -> IRQ 19
IOAPIC[0]: Set PCI routing entry (2-16 -> 0xb9 -> IRQ 16 Mode:1 Active:1)
00:00:0b[C] -> 2-16 -> IRQ 16
IOAPIC[0]: Set PCI routing entry (2-17 -> 0xc1 -> IRQ 17 Mode:1 Active:1)
00:00:0b[D] -> 2-17 -> IRQ 17
Pin 2-19 already programmed
Pin 2-18 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
IOAPIC[0]: Set PCI routing entry (2-23 -> 0xc9 -> IRQ 23 Mode:1 Active:1)
00:00:02[A] -> 2-23 -> IRQ 23
IOAPIC[0]: Set PCI routing entry (2-21 -> 0xd1 -> IRQ 21 Mode:1 Active:1)
00:00:02[B] -> 2-21 -> IRQ 21
Pin 2-21 already programmed
IOAPIC[0]: Set PCI routing entry (2-20 -> 0xd9 -> IRQ 20 Mode:1 Active:1)
00:00:02[D] -> 2-20 -> IRQ 20
IOAPIC[0]: Set PCI routing entry (2-22 -> 0xe1 -> IRQ 22 Mode:1 Active:1)
00:00:03[A] -> 2-22 -> IRQ 22
Pin 2-22 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178014
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0014
An unexpected IO-APIC was found. If this kernel release is less than
three months old please report this to linux-smp@vger.kernel.org
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 0 1 0 1 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 001 01 1 1 0 1 0 1 1 B9
11 001 01 1 1 0 1 0 1 1 C1
12 001 01 1 1 0 1 0 1 1 A9
13 001 01 1 1 0 1 0 1 1 B1
14 001 01 1 1 0 1 0 1 1 D9
15 001 01 1 1 0 1 0 1 1 D1
16 001 01 1 1 0 1 0 1 1 E1
17 001 01 1 1 0 1 0 1 1 C9
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9-> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ20 -> 0:20
IRQ21 -> 0:21
IRQ22 -> 0:22
IRQ23 -> 0:23
.................................... done.
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even
'acpi=off'
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [FUTS]
ACPI: Fan [FAN] (on)
ACPI: Processor [CPU0] (supports C1)
ACPI: Thermal Zone [THRM] (25 C)
keyboard: Timeout - AT keyboard not present?(ed)
keyboard: Timeout - AT keyboard not present?(f4)
pty: 256 Unix98 ptys configured
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller at PCI slot 00:02.5
SIS5513: chipset revision 208
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 961 MuTIOL IDE UDMA100 controller
ide0: BM-DMA at 0x4000-0x4007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x4008-0x400f, BIOS settings: hdc:DMA, hdd:pio
hda: SAMSUNG SV8004H, ATA DISK drive
hdb: Hitachi XXM2.3.0, CFA DISK drive
blk: queue c0314e40, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c0314f7c, I/O limit 4095Mb (mask 0xffffffff)
hdc: _NEC DVD_RW ND-1300A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 156368016 sectors (80060 MB) w/2048KiB Cache, CHS=9733/255/63,
UDMA(100)
hdb: attached ide-disk driver.
hdb: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
hdb: task_no_data_intr: error=0x04 { DriveStatusError }
hdb: 500400 sectors (256 MB) w/1KiB Cache, CHS=695/15/48, BUG
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3
/dev/ide/host0/bus0/target1/lun0:hdb: dma_intr: status=0x51 { DriveReady
SeekComplete Error }
hdb: dma_intr: error=0x04 { DriveStatusError }
hdb: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdb: dma_intr: error=0x04 { DriveStatusError }
hdb: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdb: dma_intr: error=0x04 { DriveStatusError }
hdb: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdb: dma_intr: error=0x04 { DriveStatusError }
hda: DMA disabled
hdb: DMA disabled
ide0: reset: success
p1
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
reiserfs: found format "3.6" with standard journal
reiserfs: checking transaction log (device ide0(3,3)) ...
for (ide0(3,3))
ide0(3,3):Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 120k freed
VFS: Disk change detected on device 03:40
/dev/ide/host0/bus0/target1/lun0: p1
Adding Swap: 498004k swap-space (priority -1)
attempt to access beyond end of device
03:03: rw=0, want=77585920, limit=77585917
SCSI subsystem driver Revision: 1.00
hdc: attached ide-scsi driver.
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: _NEC Model: DVD_RW ND-1300A Rev: 1.08
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
8139too Fast Ethernet driver 0.9.26
eth0: RealTek RTL8139 at 0xce927000, 00:30:1b:11:23:c6, IRQ 18
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
lirc_serial: auto-detected active low receiver
Non-volatile memory driver v1.2
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-ohci.c: USB OHCI at membase 0xce990000, IRQ 20
usb-ohci.c: usb-00:02.2, Silicon Integrated Systems [SiS] USB 1.0 Controller
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 3 ports detected
usb-ohci.c: USB OHCI at membase 0xce992000, IRQ 23
usb-ohci.c: usb-00:02.3, Silicon Integrated Systems [SiS] USB 1.0 Controller
(#2)
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 3 ports detected
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
cdfs 0.5c loaded.
Real Time Clock Driver v1.10f
hub.c: new USB device 00:02.2-1, assigned address 2
usb.c: USB device 2 (vend/prod 0x967/0x204) is not claimed by any active
driver.
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
prism2_init: prism2_usb.o: 0.2.1-pre16 Loaded
prism2_init: dev_info is: prism2_usb
usb.c: registered new driver prism2_usb
ident: nic h/w: id=0x8026 1.0.0
ident: pri f/w: id=0x15 1.1.2
ident: sta f/w: id=0x1f 1.5.6
MFI:SUP:role=0x00:id=0x01:var=0x01:b/t=1/1
CFI:SUP:role=0x00:id=0x02:var=0x02:b/t=1/1
PRI:SUP:role=0x00:id=0x03:var=0x01:b/t=1/4
STA:SUP:role=0x00:id=0x04:var=0x01:b/t=1/10
PRI-CFI:ACT:role=0x01:id=0x02:var=0x02:b/t=1/1
STA-CFI:ACT:role=0x01:id=0x02:var=0x02:b/t=1/1
STA-MFI:ACT:role=0x01:id=0x01:var=0x01:b/t=1/1
Prism2 card SN: 0\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00
blk: queue c0314e40, I/O limit 4095Mb (mask 0xffffffff)
linkstatus=CONNECTED
# lspci -v
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 740 Host (rev 01)
Subsystem: Silicon Integrated Systems [SiS] 740 Host
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 32
Region 0: Memory at e8000000 (32-bit, non-prefetchable) [size=32M]
Capabilities: [c0] AGP version 2.0
Status: RQ=16 SBA+ 64bit- FW+ Rate=x1,x2,x4
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] 5591/5592 AGP (prog-if
00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 99
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: ea000000-ea0fffff
Prefetchable memory behind bridge: e0000000-e7ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:02.0 ISA bridge: Silicon Integrated Systems [SiS] 85C503/5513
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
00:02.2 USB Controller: Silicon Integrated Systems [SiS] 7001 (rev 07)
(prog-if 10 [OHCI])
Subsystem: Silicon Integrated Systems [SiS] 7001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32 (20000ns max), cache line size 08
Interrupt: pin D routed to IRQ 20
Region 0: Memory at ea100000 (32-bit, non-prefetchable) [size=4K]
00:02.3 USB Controller: Silicon Integrated Systems [SiS] 7001 (rev 07)
(prog-if 10 [OHCI])
Subsystem: Silicon Integrated Systems [SiS] 7001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32 (20000ns max), cache line size 08
Interrupt: pin A routed to IRQ 23
Region 0: Memory at ea101000 (32-bit, non-prefetchable) [size=4K]
00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0)
(prog-if 80 [Master])
Subsystem: Silicon Integrated Systems [SiS] SiS5513 EIDE Controller (A,B
step)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 128
Region 4: I/O ports at 4000 [size=16]
00:0a.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device f440
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at e000 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0b.0 Multimedia video controller: Brooktree Corporation Bt878 Video
Capture (rev 02)
Subsystem: Hauppauge computer works Inc. WinTV/GO
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 18
Region 0: Memory at ea102000 (32-bit, prefetchable) [size=4K]
00:0b.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture
(rev 02)
Subsystem: Hauppauge computer works Inc. WinTV/GO
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 18
Region 0: Memory at ea103000 (32-bit, prefetchable) [size=4K]
00:0c.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
Subsystem: Technotrend Systemtechnik GmbH: Unknown device 0002
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32 (3750ns min, 9500ns max)
Interrupt: pin A routed to IRQ 19
Region 0: Memory at ea104000 (32-bit, non-prefetchable) [size=512]
00:0f.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at e400 [size=256]
Region 1: Memory at ea105000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.0 FireWire (IEEE 1394): Lucent Microelectronics FW323 (rev 04)
(prog-if 10 [OHCI])
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device f024
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32 (3000ns min, 6000ns max), cache line size 08
Interrupt: pin A routed to IRQ 19
Region 0: Memory at ea106000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS]: Unknown
device 6325 (prog-if 00 [VGA])
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device f440
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
BIST result: 00
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at ea000000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at d000 [size=128]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] AGP version 2.0
Status: RQ=15 SBA+ 64bit- FW- Rate=x1,x2,x4
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
--
+++ GMX - die erste Adresse für Mail, Message, More +++
Neu: Preissenkung für MMS und FreeMMS! http://www.gmx.net
-
To unsubscribe from this list: send the line "unsubscribe linux-smp" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
[prev in list] [next in list] [prev in thread] [next in thread]
Configure |
About |
News |
Add a list |
Sponsored by KoreLogic