[prev in list] [next in list] [prev in thread] [next in thread]
List: linux-smp
Subject: kernel messages about unexpected IO-APIC
From: Kenneth Emmons Jr <kenemmons () yahoo ! com>
Date: 2001-09-27 0:11:04
[Download RAW message or body]
A kernel message said I should email it to this address, see the attached
kernel message output file.
~Ken
["io-apic.dmesg.out" (text/plain)]
g 0a
per-CPU timeslice cutoff: 730.97 usecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Booting processor 1/1 eip 3000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 1992.29 BogoMIPS
CPU: Before vendor init, caps: 0387fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check reporting enabled on CPU#1.
CPU: After vendor init, caps: 0387fbff 00000000 00000000 00000000
CPU serial number disabled.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU1: Intel Pentium III (Coppermine) stepping 0a
Total of 2 processors activated (3984.58 BogoMIPS).
ENABLING IO-APIC IRQs
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not \
connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 16.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00178011
....... : max redirection entries: 0017
....... : IO APIC version: 0011
WARNING: unexpected IO-APIC, please mail
to linux-smp@vger.kernel.org
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 003 03 0 0 0 0 0 1 1 39
02 003 03 0 0 0 0 0 1 1 31
03 003 03 0 0 0 0 0 1 1 41
04 003 03 0 0 0 0 0 1 1 49
05 003 03 1 1 0 1 0 1 1 51
06 003 03 0 0 0 0 0 1 1 59
07 003 03 0 0 0 0 0 1 1 61
08 003 03 0 0 0 0 0 1 1 69
09 003 03 1 1 0 1 0 1 1 71
0a 003 03 1 1 0 1 0 1 1 79
0b 003 03 1 1 0 1 0 1 1 81
0c 003 03 0 0 0 0 0 1 1 89
0d 003 03 0 0 0 0 0 1 1 91
0e 003 03 0 0 0 0 0 1 1 99
0f 003 03 0 0 0 0 0 1 1 A1
10 000 00 1 0 0 0 0 0 0 00
11 000 00 1 0 0 0 0 0 0 00
12 000 00 1 0 0 0 0 0 0 00
13 000 00 1 0 0 0 0 0 0 00
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 998.4185 MHz.
..... host bus clock speed is 133.1222 MHz.
cpu: 0, clocks: 1331222, slice: 443740
CPU0<T0:1331216,T1:887472,D:4,S:443740,C:1331222>
cpu: 1, clocks: 1331222, slice: 443740
CPU1<T0:1331216,T1:443728,D:8,S:443740,C:1331222>
checking TSC synchronization across CPUs: passed.
mtrr: your CPUs had inconsistent variable MTRR settings
mtrr: probably your BIOS does not setup all CPUs
PCI: PCI BIOS revision 2.10 entry at 0xfb370, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router VIA [1106/0686] at 00:07.0
PCI: Enabling Via external APIC routing
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PnP: PNP BIOS installation structure at 0xc00fbd80
PnP: PNP BIOS version 1.0, entry at f0000:bdb0, dseg at f0000
PnP: 14 devices detected total
PNPBIOS: request ports [PNP0c01]:
PNPBIOS: request ports [PNP0c02]:
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.14)
apm: disabled - APM is not SMP safe.
Starting kswapd v1.8
allocated 32 pages and 32 bhs reserved for the highmem bounces
VFS: Diskquotas version dquot_6.5.0 initialized
devfs: v0.115 (20010827) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
vesafb: framebuffer at 0xd0000000, mapped to 0xf8800000, size 32768k
vesafb: mode is 800x600x16, linelength=1600, pages=3
vesafb: protected mode interface info at c000:c2c0
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 100x37
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ \
SERIAL_PCI ISAPNP enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
block: queued sectors max/low 682858kB/551786kB, 2048 slots per queue
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 39
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:07.1
ide0: BM-DMA at 0xc000-0xc007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xc008-0xc00f, BIOS settings: hdc:pio, hdd:pio
HPT370: IDE controller on PCI bus 00 dev 70
HPT370: chipset revision 3
HPT370: not 100% native mode: will probe irqs later
ide2: BM-DMA at 0xec00-0xec07, BIOS settings: hde:DMA, hdf:pio
ide3: BM-DMA at 0xec08-0xec0f, BIOS settings: hdg:DMA, hdh:pio
hda: Pioneer DVD-ROM ATAPIModel DVD-105S 012, ATAPI CD/DVD-ROM drive
hde: WDC WD400BB-75AUA1, ATA DISK drive
hdg: WDC WD400BB-75AUA1, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide2 at 0xdc00-0xdc07,0xe002 on irq 11
ide3 at 0xe400-0xe407,0xe802 on irq 11
hde: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=77545/16/63, UDMA(100)
hdg: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=77545/16/63, UDMA(100)
hda: ATAPI 40X DVD-ROM drive, 512kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
ide-floppy driver 0.97
Partition check:
/dev/ide/host2/bus0/target0/lun0: p1 p2 < p5 p6 >
/dev/ide/host2/bus1/target0/lun0: p1 p2 < p5 p6 >
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
ide-floppy driver 0.97
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
(read) ide/host2/bus0/target0/lun0/part5's sb offset: 4202240 [events: 00000011]
(read) ide/host2/bus0/target0/lun0/part6's sb offset: 34669504 [events: 00000011]
(read) ide/host2/bus1/target0/lun0/part5's sb offset: 4202240 [events: 00000011]
(read) ide/host2/bus1/target0/lun0/part6's sb offset: 34669504 [events: 00000011]
md: autorun ...
md: considering ide/host2/bus1/target0/lun0/part6 ...
md: adding ide/host2/bus1/target0/lun0/part6 ...
md: adding ide/host2/bus0/target0/lun0/part6 ...
md: created md1
md: bind<ide/host2/bus0/target0/lun0/part6,1>
md: bind<ide/host2/bus1/target0/lun0/part6,2>
md: running: <ide/host2/bus1/target0/lun0/part6><ide/host2/bus0/target0/lun0/part6>
md: now!
md: ide/host2/bus1/target0/lun0/part6's event counter: 00000011
md: ide/host2/bus0/target0/lun0/part6's event counter: 00000011
request_module[md-personality-2]: Root fs not mounted
md.c: personality 2 is not loaded!
md :do_md_run() returned -22
md: md1 stopped.
md: unbind<ide/host2/bus1/target0/lun0/part6,1>
md: export_rdev(ide/host2/bus1/target0/lun0/part6)
md: unbind<ide/host2/bus0/target0/lun0/part6,0>
md: export_rdev(ide/host2/bus0/target0/lun0/part6)
md: considering ide/host2/bus1/target0/lun0/part5 ...
md: adding ide/host2/bus1/target0/lun0/part5 ...
md: adding ide/host2/bus0/target0/lun0/part5 ...
md: created md0
md: bind<ide/host2/bus0/target0/lun0/part5,1>
md: bind<ide/host2/bus1/target0/lun0/part5,2>
md: running: <ide/host2/bus1/target0/lun0/part5><ide/host2/bus0/target0/lun0/part5>
md: now!
md: ide/host2/bus1/target0/lun0/part5's event counter: 00000011
md: ide/host2/bus0/target0/lun0/part5's event counter: 00000011
request_module[md-personality-2]: Root fs not mounted
md.c: personality 2 is not loaded!
md :do_md_run() returned -22
md: md0 stopped.
md: unbind<ide/host2/bus1/target0/lun0/part5,1>
md: export_rdev(ide/host2/bus1/target0/lun0/part5)
md: unbind<ide/host2/bus0/target0/lun0/part5,0>
md: export_rdev(ide/host2/bus0/target0/lun0/part5)
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Uncompressing............done.
Freeing initrd memory: 290k freed
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
md: raid0 personality registered as nr 2
md: Autodetecting RAID arrays.
(read) ide/host2/bus1/target0/lun0/part6's sb offset: 34669504 [events: 00000011]
(read) ide/host2/bus0/target0/lun0/part6's sb offset: 34669504 [events: 00000011]
(read) ide/host2/bus1/target0/lun0/part5's sb offset: 4202240 [events: 00000011]
(read) ide/host2/bus0/target0/lun0/part5's sb offset: 4202240 [events: 00000011]
md: autorun ...
md: considering ide/host2/bus0/target0/lun0/part5 ...
md: adding ide/host2/bus0/target0/lun0/part5 ...
md: adding ide/host2/bus1/target0/lun0/part5 ...
md: created md0
md: bind<ide/host2/bus1/target0/lun0/part5,1>
md: bind<ide/host2/bus0/target0/lun0/part5,2>
md: running: <ide/host2/bus0/target0/lun0/part5><ide/host2/bus1/target0/lun0/part5>
md: now!
md: ide/host2/bus0/target0/lun0/part5's event counter: 00000011
md: ide/host2/bus1/target0/lun0/part5's event counter: 00000011
md0: max total readahead window set to 512k
md0: 2 data-disks, max readahead per data-disk: 256k
raid0: looking at ide/host2/bus0/target0/lun0/part5
raid0: comparing ide/host2/bus0/target0/lun0/part5(4202240) with \
ide/host2/bus0/target0/lun0/part5(4202240)
raid0: END
raid0: ==> UNIQUE
raid0: 1 zones
raid0: looking at ide/host2/bus1/target0/lun0/part5
raid0: comparing ide/host2/bus1/target0/lun0/part5(4202240) with \
ide/host2/bus0/target0/lun0/part5(4202240)
raid0: EQUAL
raid0: FINAL 1 zones
raid0: zone 0
raid0: checking ide/host2/bus0/target0/lun0/part5 ... contained as device 0
(4202240) is smallest!.
raid0: checking ide/host2/bus1/target0/lun0/part5 ... contained as device 1
raid0: zone->nb_dev: 2, size: 8404480
raid0: current zone offset: 4202240
raid0: done.
raid0 : md_size is 8404480 blocks.
raid0 : conf->smallest->size is 8404480 blocks.
raid0 : nb_zone is 1.
raid0 : Allocating 8 bytes for hash.
md: updating md0 RAID superblock on device
md: ide/host2/bus0/target0/lun0/part5 [events: 00000012](write) \
ide/host2/bus0/target0/lun0/part5's sb offset: 4202240
md: ide/host2/bus1/target0/lun0/part5 [events: 00000012](write) \
ide/host2/bus1/target0/lun0/part5's sb offset: 4202240
md: considering ide/host2/bus0/target0/lun0/part6 ...
md: adding ide/host2/bus0/target0/lun0/part6 ...
md: adding ide/host2/bus1/target0/lun0/part6 ...
md: created md1
md: bind<ide/host2/bus1/target0/lun0/part6,1>
md: bind<ide/host2/bus0/target0/lun0/part6,2>
md: running: <ide/host2/bus0/target0/lun0/part6><ide/host2/bus1/target0/lun0/part6>
md: now!
md: ide/host2/bus0/target0/lun0/part6's event counter: 00000011
md: ide/host2/bus1/target0/lun0/part6's event counter: 00000011
md1: max total readahead window set to 512k
md1: 2 data-disks, max readahead per data-disk: 256k
raid0: looking at ide/host2/bus1/target0/lun0/part6
raid0: comparing ide/host2/bus1/target0/lun0/part6(34669504) with \
ide/host2/bus1/target0/lun0/part6(34669504)
raid0: END
raid0: ==> UNIQUE
raid0: 1 zones
raid0: looking at ide/host2/bus0/target0/lun0/part6
raid0: comparing ide/host2/bus0/target0/lun0/part6(34669504) with \
ide/host2/bus1/target0/lun0/part6(34669504)
raid0: EQUAL
raid0: FINAL 1 zones
raid0: zone 0
raid0: checking ide/host2/bus1/target0/lun0/part6 ... contained as device 0
(34669504) is smallest!.
raid0: checking ide/host2/bus0/target0/lun0/part6 ... contained as device 1
raid0: zone->nb_dev: 2, size: 69339008
raid0: current zone offset: 34669504
raid0: done.
raid0 : md_size is 69339008 blocks.
raid0 : conf->smallest->size is 69339008 blocks.
raid0 : nb_zone is 1.
raid0 : Allocating 8 bytes for hash.
md: updating md1 RAID superblock on device
md: ide/host2/bus0/target0/lun0/part6 [events: 00000012](write) \
ide/host2/bus0/target0/lun0/part6's sb offset: 34669504
md: ide/host2/bus1/target0/lun0/part6 [events: 00000012](write) \
ide/host2/bus1/target0/lun0/part6's sb offset: 34669504
md: ... autorun DONE.
Freeing unused kernel memory: 248k freed
Creative EMU10K1 PCI Audio Driver, version 0.15, 16:28:35 Sep 5 2001
emu10k1: EMU10K1 rev 7 model 0x8061 found, IO at 0xd000-0xd01f, IRQ 10
ac97_codec: AC97 Audio codec, id: 0x8384:0x7608 (SigmaTel STAC9708)
PnPBIOS: Parport found PNPBIOS PNP0400 at io=0378,0000 irq=7 dma=-1
parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport_pc: Strange, can't probe Via 686A parallel port: io=0x378, irq=-1, dma=-1
lp0: using parport0 (interrupt-driven).
Real Time Clock Driver v1.10d
Adding Swap: 210632k swap-space (priority -1)
md: fsck.ext2(pid 242) used obsolete MD ioctl, upgrade your software to use new \
ictls.
md: fsck.ext2(pid 310) used obsolete MD ioctl, upgrade your software to use new \
ictls.
ip_tables: (c)2000 Netfilter core team
ip_conntrack (8191 buckets, 65528 max)
Linux Tulip driver version 0.9.15-pre6 (July 2, 2001)
eth0: ADMtek Comet rev 17 at 0xcc00, 00:03:6D:14:5D:26, IRQ 10.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.259 $ time 16:29:55 Sep 5 2001
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xc400, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xc800, IRQ 9
usb-uhci.c: Detected 2 ports
hub.c: USB new device connect on bus1/1, assigned device number 2
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: USB device 2 (vend/prod 0x3f0/0x212) is not claimed by any active driver.
usb-uhci.c: v1.251:USB Universal Host Controller Interface driver
hub.c: USB new device connect on bus1/2, assigned device number 3
hub.c: USB hub found
hub.c: 4 ports detected
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: ipvs loaded.
usb.c: registered new driver usblp
printer.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 1
printer.c: v0.8:USB Printer Device Class driver
IPVS: ipvs unloaded.
Creative EMU10K1 PCI Audio Driver, version 0.15, 16:28:35 Sep 5 2001
emu10k1: EMU10K1 rev 7 model 0x8061 found, IO at 0xd000-0xd01f, IRQ 10
ac97_codec: AC97 Audio codec, id: 0x8384:0x7608 (SigmaTel STAC9708)
_________________________________________________________
Do You Yahoo!?
Get your free @yahoo.com address at http://mail.yahoo.com
-
To unsubscribe from this list: send the line "unsubscribe linux-smp" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
[prev in list] [next in list] [prev in thread] [next in thread]
Configure |
About |
News |
Add a list |
Sponsored by KoreLogic