[prev in list] [next in list] [prev in thread] [next in thread] 

List:       linux-mmc
Subject:    Re: [PATCH v2] mmc: sdhci-acpi: AMDI0040: Allow changing HS200/HS400 driver strength
From:       Ulf Hansson <ulf.hansson () linaro ! org>
Date:       2020-10-27 13:41:56
Message-ID: CAPDyKFo=jA84Zr9AM7sXR_VxpGsi9n-aGJJMRcY7uFBcRWrf4g () mail ! gmail ! com
[Download RAW message or body]

On Tue, 27 Oct 2020 at 09:46, Victor Ding <victording@google.com> wrote:
> 
> From: Raul E Rangel <rrangel@chromium.org>
> 
> This change will allow platform designers better control over signal
> integrity by allowing them to tune the HS200 and HS400 driver strengths.
> 
> The driver strength was previously hard coded to A to solve boot
> problems with certain platforms. This driver strength does not
> universally apply to all platforms so we need a knob to adjust it.
> 
> All older platforms currently have the SDR104 preset hard coded to A in
> the firmware. This means that switching from the hard coded value in
> the kernel to reading the SDR104 preset is a no-op for these platforms.
> Newer platforms will have properly set presets. So this change will
> support both new and old platforms.
> 
> Signed-off-by: Raul E Rangel <rrangel@chromium.org>
> Signed-off-by: Victor Ding <victording@google.com>

Applied for next, thanks!

Note that I amended the patch to fix the white-space issue, as pointed
out by Adrian.

Kind regards
Uffe


> 
> ---
> 
> Changes in v2:
> By Victor Ding <victording@google.com>
> - Rebased the patch by using FIELD_GET for preset value bit masks.
> - (No functional changes).
> 
> The original patch was developed by Raul E Rangel.
> https://patchwork.kernel.org/project/linux-mmc/patch/20200928154718.2.Ic6b6031366f090393d00a53fd69e1ada31ceb29e@changeid/
>  
> drivers/mmc/host/sdhci-acpi.c | 39 ++++++++++++++++++++++++++++++++---
> 1 file changed, 36 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/mmc/host/sdhci-acpi.c b/drivers/mmc/host/sdhci-acpi.c
> index 54205e3be9e8..225cb34cf1b9 100644
> --- a/drivers/mmc/host/sdhci-acpi.c
> +++ b/drivers/mmc/host/sdhci-acpi.c
> @@ -5,6 +5,7 @@
> * Copyright (c) 2012, Intel Corporation.
> */
> 
> +#include <linux/bitfield.h>
> #include <linux/init.h>
> #include <linux/export.h>
> #include <linux/module.h>
> @@ -545,10 +546,42 @@ struct amd_sdhci_host {
> 
> static int amd_select_drive_strength(struct mmc_card *card,
> unsigned int max_dtr, int host_drv,
> -                                    int card_drv, int *drv_type)
> +                                    int card_drv, int *host_driver_strength)
> {
> -       *drv_type = MMC_SET_DRIVER_TYPE_A;
> -       return MMC_SET_DRIVER_TYPE_A;
> +       struct sdhci_host *host = mmc_priv(card->host);
> +       u16 preset, preset_driver_strength;
> +
> +       /*
> +        * This method is only called by mmc_select_hs200 so we only need to
> +        * read from the HS200 (SDR104) preset register.
> +        *
> +        * Firmware that has "invalid/default" presets return a driver strength
> +        * of A. This matches the previously hard coded value.
> +        */
> +       preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR104);
> +       preset_driver_strength = FIELD_GET(SDHCI_PRESET_DRV_MASK, preset);
> +
> +       /*
> +        * We want the controller driver strength to match the card's driver
> +        * strength so they have similar rise/fall times.
> +        *
> +        * The controller driver strength set by this method is sticky for all
> +        * timings after this method is called. This unfortunately means that
> +        * while HS400 tuning is in progress we end up with mismatched driver
> +        * strengths between the controller and the card. HS400 tuning requires
> +        * switching from HS400->DDR52->HS->HS200->HS400. So the driver mismatch
> +        * happens while in DDR52 and HS modes. This has not been observed to
> +        * cause problems. Enabling presets would fix this issue.
> +        */
> +       *host_driver_strength = preset_driver_strength;
> +
> +       /*
> +        * The resulting card driver strength is only set when switching the
> +        * card's timing to HS200 or HS400. The card will use the default driver
> +        * strength (B) for any other mode.
> +        */
> +       return preset_driver_strength;
> +
> }
> 
> static void sdhci_acpi_amd_hs400_dll(struct sdhci_host *host, bool enable)
> --
> 2.29.0.rc2.309.g374f81d7ae-goog
> 


[prev in list] [next in list] [prev in thread] [next in thread]