[prev in list] [next in list] [prev in thread] [next in thread]
List: linux-mmc
Subject: [PATCH] mmc: mmci: Send a CMD12 to clear the DPSM at errors
From: Ulf Hansson <ulf.hansson () linaro ! org>
Date: 2019-01-29 14:35:56
Message-ID: 20190129143556.32705-1-ulf.hansson () linaro ! org
[Download RAW message or body]
The current approach with sending a CMD12 (STOP_TRANSMISSION) to complete a
data transfer request, either because of using the open-ended transmission
type or because of receiving an error during a pre-defined data transfer,
isn't sufficient for the STM32 sdmmc variant. More precisely, this variant
needs to clear the DPSM ("Data Path State Machine") by sending a CMD12, for
all failing ADTC commands.
Support this, by adding a struct mmc_command inside the struct mmci_host
and initialize it to a CMD12 during ->probe(). Let's also add checks for
the new conditions, to enable mmci_data_irq() and mmci_cmd_irq() to
postpone the calls to mmci_request_end(), but instead send the CMD12.
Cc: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
---
drivers/mmc/host/mmci.c | 25 +++++++++++++++++++++++--
drivers/mmc/host/mmci.h | 1 +
2 files changed, 24 insertions(+), 2 deletions(-)
diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index e352f5ad5801..45b97b41601c 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -1127,6 +1127,12 @@ mmci_start_command(struct mmci_host *host, struct mmc_command *cmd, u32 c)
writel(c, base + MMCICOMMAND);
}
+static void mmci_stop_command(struct mmci_host *host)
+{
+ host->stop_abort.error = 0;
+ mmci_start_command(host, &host->stop_abort, 0);
+}
+
static void
mmci_data_irq(struct mmci_host *host, struct mmc_data *data,
unsigned int status)
@@ -1196,10 +1202,16 @@ mmci_data_irq(struct mmci_host *host, struct mmc_data *data,
/* The error clause is handled above, success! */
data->bytes_xfered = data->blksz * data->blocks;
- if (!data->stop || (host->mrq->sbc && !data->error))
+ if (!data->stop) {
+ if (host->variant->cmdreg_stop && data->error)
+ mmci_stop_command(host);
+ else
+ mmci_request_end(host, data->mrq);
+ } else if (host->mrq->sbc && !data->error) {
mmci_request_end(host, data->mrq);
- else
+ } else {
mmci_start_command(host, data->stop, 0);
+ }
}
}
@@ -1298,6 +1310,10 @@ mmci_cmd_irq(struct mmci_host *host, struct mmc_command *cmd,
mmci_dma_error(host);
mmci_stop_data(host);
+ if (host->variant->cmdreg_stop && cmd->error) {
+ mmci_stop_command(host);
+ return;
+ }
}
mmci_request_end(host, host->mrq);
} else if (sbc) {
@@ -1956,6 +1972,11 @@ static int mmci_probe(struct amba_device *dev,
mmc->max_busy_timeout = 0;
}
+ /* Prepare a CMD12 - needed to clear the DPSM on some variants. */
+ host->stop_abort.opcode = MMC_STOP_TRANSMISSION;
+ host->stop_abort.arg = 0;
+ host->stop_abort.flags = MMC_RSP_R1B | MMC_CMD_AC;
+
mmc->ops = &mmci_ops;
/* We support these PM capabilities. */
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index 24229097d05c..14df81054438 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -377,6 +377,7 @@ struct mmci_host {
void __iomem *base;
struct mmc_request *mrq;
struct mmc_command *cmd;
+ struct mmc_command stop_abort;
struct mmc_data *data;
struct mmc_host *mmc;
struct clk *clk;
--
2.17.1
[prev in list] [next in list] [prev in thread] [next in thread]
Configure |
About |
News |
Add a list |
Sponsored by KoreLogic