[prev in list] [next in list] [prev in thread] [next in thread]
List: linux-kernel
Subject: Misc errors
From: Anders.Ohrt () home ! se (=?ISO-8859-1?Q?Anders_=D6hrt?=)
Date: 2000-03-31 21:36:33
[Download RAW message or body]
I just tried 2.3.99-pre3 and found some oddities... First, I tried
compiling, and got 2 undefined references. Seems I choose to compile
ide as module, since I run scsi but have an ide cdrom, and that meant
ide.c didn't get compiled. Makefile problems I guess.
Then everything went fine until I added 2.3.99 in lilo.conf and wrote
'lilo'. I then got 8 "hda: driver not present". That's strange... And
when trying to paste the errors into a file, xemacs semfaulted. It now
does so every time I paste something using the mouse.
I also got the hda errors on boot...
Attaching my lilo.conf, the lilo error output, and my dmesg output:
lilo.conf:
boot=/dev/sda4
root=/dev/sda4
install=/boot/boot.b
map=/boot/map
vga=extended
delay=0
image=/boot/bzImage-2.3.99-pre3
label="2.3.99-pre3"
vga=extended
read-only
image=/boot/bzImage-2.2.11-experimental
label="Debian 2.2.11"
vga=extended
read-only
image=/boot/bzImage-2.2.11
label="2.2.11 old"
vga=extended
read-only
image=/boot/vmlinuz-2.0.36
label="Debian 2.0.36"
vga=normal
read-only
---
Lilo error output:
# lilo
hda: driver not present
hda: driver not present
hda: driver not present
hda: driver not present
hda: driver not present
Added 2.3.99-pre3 *
hda: driver not present
Added Debian 2.2.11
hda: driver not present
Added 2.2.11 old
hda: driver not present
Added Debian 2.0.36
---
dmesg:
Linux version 2.3.99-pre3 (root@doas-place) (gcc version 2.95.2
20000220 (Debian GNU/Linux)) #14 Fri Mar 31 23:18:00 CEST 2000
e820: 0009fc00 @ 00000000 (usable)
e820: 00000400 @ 0009fc00 (reserved)
e820: 00010000 @ 000f0000 (reserved)
e820: 00010000 @ ffff0000 (reserved)
e820: 07f00000 @ 00100000 (usable)
Scan SMP from c0000000 for 1024 bytes.
Scan SMP from c009fc00 for 1024 bytes.
Scan SMP from c00f0000 for 65536 bytes.
Scan SMP from c009f800 for 4096 bytes.
On node 0 totalpages: 32768
zone(0): 4096 pages.
zone(1): 28672 pages.
zone(2): 0 pages.
mapped APIC to ffffe000 (01243000)
Initializing CPU#0
Detected 360825987 Hz processor.
Console: colour VGA+ 80x50
Calibrating delay loop... 719.26 BogoMIPS
Memory: 126304k/131072k available (1286k kernel code, 4380k reserved,
105k data, 200k init, 0k highmem)
Buffer-cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
CPU: Intel Pentium II (Deschutes) stepping 00
Checking 386/387 coupling... OK, FPU using exception 16 error
reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.36 (20000221) Richard Gooch (rgooch@atnf.csiro.au)
PCI: PCI BIOS revision 2.10 entry at 0xfb460
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Interrupt Routing Table found at 0xc00fdf00 [router type
8086/7000]
Limiting direct PCI/PCI transfers.
Linux NET4.0 for Linux 2.3
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
IPv6 v0.8 for NET4.0
IPv6 over IPv4 tunneling driver
early initialization of device sit0 is deferred
Starting kswapd v1.6
pty: 256 Unix98 ptys configured
Uniform Multi-Platform E-IDE driver Revision: 6.30
ide: Assuming 40MHz system bus speed for PIO modes; override with
idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
hda: Pioneer CD-ROM ATAPI Model DR-A14S 0104, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
ncr53c8xx: at PCI bus 0, device 15, function 0
ncr53c8xx: 53c895 detected with Tekram NVRAM
ncr53c895-0: rev 0x1 on pci bus 0 device 15 function 0 irq 11
ncr53c895-0: Tekram format NVRAM, ID 7, Fast-40, Parity Checking
ncr53c895-0: on-chip RAM at 0xef001000
ncr53c895-0: restart (scsi reset).
ncr53c895-0: Downloading SCSI SCRIPTS.
scsi0 : ncr53c8xx - version 3.2g
scsi : 1 host.
Vendor: QUANTUM Model: ATLAS IV 9 WLS Rev: 0808
Type: Direct-Access ANSI SCSI revision: 03
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
ncr53c895-0-<0,0>: tagged command queue depth set to 4
scsi : detected 1 SCSI disk total.
ncr53c895-0-<0,*>: FAST-40 WIDE SCSI 80.0 MB/s (25 ns, offset 31)
SCSI device sda: hdwr sector= 512 bytes. Sectors= 17942584 [8761 MB]
[8.8 GB]
Partition check:
sda: sda1 sda2 < sda5 sda6 sda7 sda8 > sda3 sda4
Serial driver version 4.93 (2000-03-20) with MANY_PORTS SHARE_IRQ
SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Linux Tulip driver version 0.9.4.2 (Mar 21, 2000)
eth0: Digital DS21140 Tulip rev 34 at 0xd400, 00:80:C8:4C:4C:DA, IRQ
9.
eth0: EEPROM default media type Autosense.
eth0: Index #0 - Media MII (#11) described by a 21140 MII PHY (1)
block.
eth0: MII transceiver #0 config 1000 status 782d advertising 01e1.
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 96M
agpgart: Detected Intel 440BX chipset
agpgart: AGP aperture is 128M @ 0xe0000000
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 200k freed
Adding Swap: 130748k swap-space (priority -1)
eth0: Setting full-duplex based on MII#0 link partner capability of
45e1.
hda: driver not present
hda: driver not present
hda: driver not present
hda: driver not present
hda: driver not present
hda: driver not present
hda: driver not present
hda: driver not present
eth0: no IPv6 routers present
---
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/
[prev in list] [next in list] [prev in thread] [next in thread]
Configure |
About |
News |
Add a list |
Sponsored by KoreLogic