[prev in list] [next in list] [prev in thread] [next in thread]
List: linux-ha
Subject: [Linux-HA] active/active configuration question, urgent,
From: Jiang <bearie66 () gmail ! com>
Date: 2006-06-27 9:17:41
Message-ID: d6e10810606270217q53e85bd2g6d86cb4b363672ef () mail ! gmail ! com
[Download RAW message or body]
Hi
I am now trying to run several services on two nodes.
The setup is as below:
VIP1: 10.226.193.230
VIP2: 10.226.193.250
Real IP 1: 10.226.193.189
Real IP 2: 10.226.193.190
Service 1 is running on both Node1 and Node 2, monitored by ldirectord.
And I have a problem when trying to configure more services, eg.
serviceA running on node 1
serviceB running on node 2
My haresources is configured like this:
*************************************************
node1 \
10.226.193.230 \
10.226.193.250 \
ldirectord::/etc/ha.d/ldirectord.cf #service 1 is
loadbalancing inside ldirectord.cf
node1 serviceA
node2 serviceB
*************************************************
During my test, whenever I shutdown heartbeat on one node, I will get
error msg on the other node:
*****************************************************
Jun 27 15:33:20 ctestsrv1 heartbeat: info: Running
/etc/ha.d/resource.d/ldirectord /etc/ha.d/ldirectord.cf start
Jun 27 15:33:21 ctestsrv1 heartbeat: ERROR: Return code 1 from
/etc/ha.d/resource.d/ldirectord
Jun 27 15:33:21 ctestsrv1 heartbeat[9249]: ERROR:
/usr/lib/heartbeat/ResourceManager takegroup 10.226.193.230
10.226.193.250 ldirectord::/etc/ha.d/ldirectord.cf returned 256
Jun 27 15:33:21 ctestsrv1 heartbeat[9249]: info: local HA resource
acquisition completed (standby).
*****************************************************
and arptable was also not fully released:
*****************************************************
Chain IN (policy ACCEPT 116K packets, 3242K bytes)
pkts bytes target in out source-ip
destination-ip source-hw destination-hw hlen op
hrd pro
0 0 DROP * * 0.0.0.0/0
10.226.193.190 00/00 00/00 any
0000/0000 0000/0000 0000/0000
Chain OUT (policy ACCEPT 12647 packets, 354K bytes)
pkts bytes target in out source-ip
destination-ip source-hw destination-hw hlen op
hrd pro
0 0 mangle * eth0 10.226.193.190 0.0.0.0/0
00/00 00/00 any 0000/0000
0000/0000 0000/0000 --mangle-ip-s 10.226.193.189
0 0 mangle * eth1 10.226.193.190 0.0.0.0/0
00/00 00/00 any 0000/0000
0000/0000 0000/0000 --mangle-ip-s 172.16.1.1
*****************************************************
Can you guys pls advice normally what is the right way to configure
haresource for my situation?
Thanks!!
--
Regards,
Jiang
_______________________________________________
Linux-HA mailing list
Linux-HA@lists.linux-ha.org
http://lists.linux-ha.org/mailman/listinfo/linux-ha
See also: http://linux-ha.org/ReportingProblems
[prev in list] [next in list] [prev in thread] [next in thread]
Configure |
About |
News |
Add a list |
Sponsored by KoreLogic