[prev in list] [next in list] [prev in thread] [next in thread]
List: linux-can
Subject: [PATCH 2/5] can: Kconfig: convert 'depends on CAN_DEV' into 'if CAN_DEV...endif' block
From: Marc Kleine-Budde <mkl () pengutronix ! de>
Date: 2012-11-29 13:58:08
Message-ID: 1354197491-31205-3-git-send-email-mkl () pengutronix ! de
[Download RAW message or body]
This patch adds an 'if CAN_DEV...endif' Block around the CAN driver
symbols in drivers/net/can/Kconfig. So the 'depends on CAN' dependencies
can be removed.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
---
drivers/net/can/Kconfig | 21 ++++++++++++---------
drivers/net/can/c_can/Kconfig | 2 +-
drivers/net/can/cc770/Kconfig | 2 +-
drivers/net/can/mscan/Kconfig | 2 +-
drivers/net/can/sja1000/Kconfig | 2 +-
drivers/net/can/softing/Kconfig | 2 +-
drivers/net/can/usb/Kconfig | 2 +-
7 files changed, 18 insertions(+), 15 deletions(-)
diff --git a/drivers/net/can/Kconfig b/drivers/net/can/Kconfig
index 8088d8f..0c5a656 100644
--- a/drivers/net/can/Kconfig
+++ b/drivers/net/can/Kconfig
@@ -36,9 +36,10 @@ config CAN_DEV
support. This is the standard library for CAN drivers.
If unsure, say Y.
+if CAN_DEV
+
config CAN_CALC_BITTIMING
bool "CAN bit-timing calculation"
- depends on CAN_DEV
default y
---help---
If enabled, CAN bit-timing parameters will be calculated for the
@@ -52,13 +53,13 @@ config CAN_CALC_BITTIMING
config CAN_AT91
tristate "Atmel AT91 onchip CAN controller"
- depends on CAN_DEV && (ARCH_AT91SAM9263 || ARCH_AT91SAM9X5)
+ depends on ARCH_AT91SAM9263 || ARCH_AT91SAM9X5
---help---
This is a driver for the SoC CAN controller in Atmel's AT91SAM9263
and AT91SAM9X5 processors.
config CAN_TI_HECC
- depends on CAN_DEV && ARCH_OMAP3
+ depends on ARCH_OMAP3
tristate "TI High End CAN Controller"
---help---
Driver for TI HECC (High End CAN Controller) module found on many
@@ -66,12 +67,12 @@ config CAN_TI_HECC
config CAN_MCP251X
tristate "Microchip MCP251x SPI CAN controllers"
- depends on CAN_DEV && SPI && HAS_DMA
+ depends on SPI && HAS_DMA
---help---
Driver for the Microchip MCP251x SPI CAN controllers.
config CAN_BFIN
- depends on CAN_DEV && (BF534 || BF536 || BF537 || BF538 || BF539 || BF54x)
+ depends on BF534 || BF536 || BF537 || BF538 || BF539 || BF54x
tristate "Analog Devices Blackfin on-chip CAN"
---help---
Driver for the Analog Devices Blackfin on-chip CAN controllers
@@ -81,7 +82,7 @@ config CAN_BFIN
config CAN_JANZ_ICAN3
tristate "Janz VMOD-ICAN3 Intelligent CAN controller"
- depends on CAN_DEV && MFD_JANZ_CMODIO
+ depends on MFD_JANZ_CMODIO
---help---
Driver for Janz VMOD-ICAN3 Intelligent CAN controller module, which
connects to a MODULbus carrier board.
@@ -94,13 +95,13 @@ config HAVE_CAN_FLEXCAN
config CAN_FLEXCAN
tristate "Support for Freescale FLEXCAN based chips"
- depends on CAN_DEV && HAVE_CAN_FLEXCAN
+ depends on HAVE_CAN_FLEXCAN
---help---
Say Y here if you want to support for Freescale FlexCAN.
config PCH_CAN
tristate "Intel EG20T PCH CAN controller"
- depends on CAN_DEV && PCI
+ depends on PCI
---help---
This driver is for PCH CAN of Topcliff (Intel EG20T PCH) which
is an IOH for x86 embedded processor (Intel Atom E6xx series).
@@ -108,7 +109,7 @@ config PCH_CAN
config CAN_GRCAN
tristate "Aeroflex Gaisler GRCAN and GRHCAN CAN devices"
- depends on CAN_DEV && OF
+ depends on OF
---help---
Say Y here if you want to use Aeroflex Gaisler GRCAN or GRHCAN.
Note that the driver supports little endian, even though little
@@ -127,6 +128,8 @@ source "drivers/net/can/usb/Kconfig"
source "drivers/net/can/softing/Kconfig"
+endif
+
config CAN_DEBUG_DEVICES
bool "CAN devices debugging messages"
---help---
diff --git a/drivers/net/can/c_can/Kconfig b/drivers/net/can/c_can/Kconfig
index 3b83baf..61ffc12 100644
--- a/drivers/net/can/c_can/Kconfig
+++ b/drivers/net/can/c_can/Kconfig
@@ -1,6 +1,6 @@
menuconfig CAN_C_CAN
tristate "Bosch C_CAN/D_CAN devices"
- depends on CAN_DEV && HAS_IOMEM
+ depends on HAS_IOMEM
if CAN_C_CAN
diff --git a/drivers/net/can/cc770/Kconfig b/drivers/net/can/cc770/Kconfig
index 22c07a8..6a9a5ba 100644
--- a/drivers/net/can/cc770/Kconfig
+++ b/drivers/net/can/cc770/Kconfig
@@ -1,6 +1,6 @@
menuconfig CAN_CC770
tristate "Bosch CC770 and Intel AN82527 devices"
- depends on CAN_DEV && HAS_IOMEM
+ depends on HAS_IOMEM
if CAN_CC770
diff --git a/drivers/net/can/mscan/Kconfig b/drivers/net/can/mscan/Kconfig
index d387069..f19be52 100644
--- a/drivers/net/can/mscan/Kconfig
+++ b/drivers/net/can/mscan/Kconfig
@@ -1,5 +1,5 @@
config CAN_MSCAN
- depends on CAN_DEV && (PPC || M68K)
+ depends on PPC || M68K
tristate "Support for Freescale MSCAN based chips"
---help---
The Motorola Scalable Controller Area Network (MSCAN) definition
diff --git a/drivers/net/can/sja1000/Kconfig b/drivers/net/can/sja1000/Kconfig
index 92f73c7..1bed54f 100644
--- a/drivers/net/can/sja1000/Kconfig
+++ b/drivers/net/can/sja1000/Kconfig
@@ -1,6 +1,6 @@
menuconfig CAN_SJA1000
tristate "Philips/NXP SJA1000 devices"
- depends on CAN_DEV && HAS_IOMEM
+ depends on HAS_IOMEM
if CAN_SJA1000
diff --git a/drivers/net/can/softing/Kconfig b/drivers/net/can/softing/Kconfig
index 5de46a9..96b6fe1 100644
--- a/drivers/net/can/softing/Kconfig
+++ b/drivers/net/can/softing/Kconfig
@@ -1,6 +1,6 @@
config CAN_SOFTING
tristate "Softing Gmbh CAN generic support"
- depends on CAN_DEV && HAS_IOMEM
+ depends on HAS_IOMEM
---help---
Support for CAN cards from Softing Gmbh & some cards
from Vector Gmbh.
diff --git a/drivers/net/can/usb/Kconfig b/drivers/net/can/usb/Kconfig
index a4e4bee..acba33d 100644
--- a/drivers/net/can/usb/Kconfig
+++ b/drivers/net/can/usb/Kconfig
@@ -1,5 +1,5 @@
menu "CAN USB interfaces"
- depends on USB && CAN_DEV
+ depends on USB
config CAN_EMS_USB
tristate "EMS CPC-USB/ARM7 CAN/USB interface"
--
1.7.10.4
--
To unsubscribe from this list: send the line "unsubscribe linux-can" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
[prev in list] [next in list] [prev in thread] [next in thread]
Configure |
About |
News |
Add a list |
Sponsored by KoreLogic