[prev in list] [next in list] [prev in thread] [next in thread] 

List:       juniper-nsp
Subject:    Re: [j-nsp] Full table inside VRF - J Series
From:       Deon Vermeulen <vermeulen.deon () gmail ! com>
Date:       2010-06-21 5:20:13
Message-ID: DEB89B14-8882-4045-AE70-CD3968CFBC04 () gmail ! com
[Download RAW message or body]

Hi Rolf,

Truman is correct.
I just found that the J4350 you are referring to (Just so that the forum knows, Rolf \
and I work for the same company) has 1Gig RAM installed on it but is already 81% \
Utilized.

*******@########> show chassis routing-engine    
Routing Engine status:
    Temperature                 30 degrees C / 86 degrees F
    CPU temperature             46 degrees C / 114 degrees F
    DRAM                      1024 MB
    Memory utilization          81 percent
    CPU utilization:
      User                       1 percent
      Real-time threads         15 percent
      Kernel                    13 percent
      Idle                      71 percent
    Model                          RE-J4350-2540
    Serial ID                      !!!!!!!!!
    Start time                     2010-04-27 22:12:59 CAT
    Uptime                         54 days, 17 hours, 25 minutes, 47 seconds
    Last reboot reason             0x8:power-button hard power off 
    Load averages:                 1 minute   5 minute  15 minute
                                       0.04       0.06       0.07

*******@########> 

According to Juniper Datasheet \
(http://www.juniper.net/us/en/local/pdf/datasheets/1000206-en.pdf) the J4350 and 6350 \
can only upgrade to max of 2Gig RAM.

The best is to LAB this and then see what the performance is after having a full \
table in an (internet) VRF.


Kind Regards

Deon Vermeulen

On Jun 21, 2010, at 5:53 AM, Truman Boyes wrote:

> Yes you can do this on a J-series. If you can handle the full table in inet.0, you \
> can handle this full table in a VRF. Just make sure you have enough RAM to hold a \
> full table (regardless of the type of routing-instance) ...  
> Truman
> 
> 
> On 20/06/2010, at 4:53 PM, Rolf Mendelsohn wrote:
> 
> > Hi All,
> > 
> > Note that my J experience is limited, I've mainly been exposed to lots of C 
> > over the years... :>).
> > 
> > We are looking to try and squeeze a Full table into a vrf on the J Series.
> > 
> > Is this possible, or is the only bet to go for an M Series or C7200/NPE-G1 or 
> > 2?
> > 
> > cheers
> > /rolf
> > 
> > 
> > _______________________________________________
> > juniper-nsp mailing list juniper-nsp@puck.nether.net
> > https://puck.nether.net/mailman/listinfo/juniper-nsp
> > 
> 
> 
> _______________________________________________
> juniper-nsp mailing list juniper-nsp@puck.nether.net
> https://puck.nether.net/mailman/listinfo/juniper-nsp


_______________________________________________
juniper-nsp mailing list juniper-nsp@puck.nether.net
https://puck.nether.net/mailman/listinfo/juniper-nsp


[prev in list] [next in list] [prev in thread] [next in thread]