[prev in list] [next in list] [prev in thread] [next in thread]
List: elecraft
Subject: Re: [Elecraft] Low Tx Data Sound Output volume
From: Bob McGraw K4TAX <rmcgraw () blomand ! net>
Date: 2017-09-28 23:31:35
Message-ID: 9DDBE9B0-0D74-47EE-A6CC-2A66FE6D68A5 () blomand ! net
[Download RAW message or body]
With FLDIGI there are two modes for DATA. PKTUSB is preferred for all modes except \
where one chooses PKTLSB for AFSK. The CAT command will handle the radio mode \
switching. Thus one does not have to turn to the radio and initiate the REV mode.
Bob, K4TAX
Sent from my iPhone
> On Sep 28, 2017, at 5:25 PM, Don Wilhelm <donwilh@embarqmail.com> wrote:
>
> Irwin,
>
> Did you get the information that Elecraft radios are different than other amateur \
> transceivers?, and that you have to set up the audio and power differently. It \
> sounds like you may not be setting the audio and power correctly for the K3/K3S.
> The common internet "advice" is to set the power to maximum, and use the audio \
> level to control the power output. That does not work well with Elecraft \
> transceivers - ignore that advice.
> With the K3 (K3S, KX3 and KX2), set the audio to produce 4 bars on the ALC meter \
> with the 5th bar flashing and adjust the power with the Power knob on the radio.
> AFSK A should be no different than LSB except that compression and TX/RX EQ is \
> automatically turned off.
> For PSK31 or other data modes, the use of DATA A submode (which is USB) is \
> recommended although PSK31 does not care about the sideband. Other soundcard \
> digital modes do care.
> Please refer to the K3 Data modes article on my website www.w3fpr.com. Scroll the \
> left column down to the bottom and you will find the link to the page.
> 73,
> Don W3FPR
>
> > On 9/25/2017 11:45 AM, Irwin Darack wrote:
> > I am not sure if this is a Windows 10 problem or something changes in my
> > K3s settings and want to see if others have experienced the same thing?
> > When the K3s is in Tx Data (PSK 31 and RTTY) - AFSK -A LSB, I now find that
> > the data output (sound) is no much lower than when just in LSB mode. This
> > seems to have occurred with the latest Windows 10 update. Hence in this
> > weekends CQWW RTTY contest, I could only use MMTTY with the K3s in LSB mode
> > and not Tx Data mode. I am not sure if it changed something with the Codec
> > driver or by some fluke, something changes in the K3s settings. Hence, I
> > ran the contest in LSB versus Tx Data.
> > Thanks,
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to rmcgraw@blomand.net
>
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to elecraft@progressive-comp.com
[prev in list] [next in list] [prev in thread] [next in thread]
Configure |
About |
News |
Add a list |
Sponsored by KoreLogic