[prev in list] [next in list] [prev in thread] [next in thread] 

List:       elecraft
Subject:    Re: [Elecraft] k2 and kpa 100
From:       Don Wilhelm <donwilh () embarqmail ! com>
Date:       2017-06-27 18:44:13
Message-ID: 056ea880-ba5d-428b-a955-fa9d5976f78a () embarqmail ! com
[Download RAW message or body]

Christophe,

With that serial number, it is set to include all that is necessary to 
add the KPA100.

Just install the P3 and P6 headers and remove pin 4 from the P4 header 
on the Control Board.
The reason for removing that pin is so the ribbon cable cannot be 
plugged in upside down.

73,
Don W3FPR

On 6/27/2017 2:30 PM, Christophe F8ACF-56 wrote:
> hi don ,
>
> my K2 # 7369 ! my firmware is 2.04R  is good to works .
>
> I take advantage of having remove the face control for C42 which was 
> of good value.
>
> The advice given is of benefit that it is filed to make the 
> modification for the KIO2
>
> Again Thanks for your help always super efficient forum!
> 73 , Christophe F8ACF-56
>
>
> ------------------------------------------------------------------------
> *De :* Don Wilhelm <donwilh@embarqmail.com>
> *À :* Christophe F8ACF-56 <f8acf56@yahoo.fr>; Elecraft Reflector 
> <elecraft@mailman.qth.net>
> *Envoyé le :* Mardi 27 juin 2017 16h01
> *Objet :* Re: [Elecraft] k2 and kpa 100
>
> Christophe,
>
> That is the modification I thought you were referring to.
>
> If your K2 serial number is 3000 or higher, that mod is already
> installed, and you do NOT have to do it.
> Notice that it refers to the REV A RF board.  Rev B boards are used in
> K2s with a serial number of 3000 or more.
> Also if your K2 is serial number 3000 or more, when you get to page 59,
> you should not do the Control Board wiring changes shown there.  Those
> changes have already been embedded on the REV B board.
>
> Yes, an infinity reading is good at the AF pad on the KPA100 board.  See
> the "I triangle" note near the top of the 2nd column on page 22.
>
> 73,
> Don W3FPR
>
> On 6/27/2017 9:31 AM, Christophe F8ACF-56 wrote:
> > Hello Don,
> >
> > It does not matter to your Frenchman, my Englishman and far from being
> > the one you master!
> >
> > I use google translation HI! To try to make me understand as well as
> > possible
> >
> > For mounting the KPA 100 I arrived on page 22, "initial test"
> > everything is OK
> >
> > But I have a doubt about "AF pad", ground.
> >
> > The measure gives infinity is this correct?
> >
> >
> >
> >
>
>
>

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to elecraft@progressive-comp.com
[prev in list] [next in list] [prev in thread] [next in thread]