[prev in list] [next in list] [prev in thread] [next in thread]
List: dpdk-dts
Subject: [dts][PATCH V1] test_plans/cvl_qinq: add test plan for cvl qinq switch filter support l4
From: Yaqi Tang <yaqi.tang () intel ! com>
Date: 2021-12-17 8:26:34
Message-ID: 20211217162521.618711-1-yaqi.tang () intel ! com
[Download RAW message or body]
CVL Support l4 for QinQ switch filter in DCF driver, and port can support as eth / \
vlan / vlan / IP / tcp|udp.
Signed-off-by: Yaqi Tang <yaqi.tang@intel.com>
Tested-by: Yaqi Tang < yaqi.tang@intel.com>
---
test_plans/cvl_qinq_test_plan.rst | 502 +++++++++++++++++++++++++++++-
1 file changed, 501 insertions(+), 1 deletion(-)
diff --git a/test_plans/cvl_qinq_test_plan.rst b/test_plans/cvl_qinq_test_plan.rst
index 4f44150b..7032d8f4 100644
--- a/test_plans/cvl_qinq_test_plan.rst
+++ b/test_plans/cvl_qinq_test_plan.rst
@@ -1533,4 +1533,504 @@ Test case 14: AVF CRC strip and Vlan strip co-exists
10:29:19.995352 00:00:00:00:00:00 > 00:11:22:33:44:11, ethertype 802.1Q \
(0x8100), length 522: vlan 1, p 0, ethertype 802.1Q, vlan 2, p 0, ethertype IPv4, \
(tos 0x0, ttl 64, id 1, offset 0, flags [none], proto Options (0), length 500) \
196.222.232.221 > 127.0.0.1: ip-proto-0 480 10:29:19.995424 00:11:22:33:44:11 > \
02:00:00:00:00:00, ethertype 802.1Q (0x8100), length 522: vlan 1, p 0, ethertype \
802.1Q, vlan 2, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 1, offset 0, flags [none], \
proto Options (0), length 500)
- 196.222.232.221 > 127.0.0.1: ip-proto-0 480
\ No newline at end of file
+ 196.222.232.221 > 127.0.0.1: ip-proto-0 480
+
+===================================+CVL DCF QINQ Switch Filter Test Plan
+===================================+
+Description
+==========+The test plan includes six test cases, such as MAC_QINQ_IPV4, \
MAC_QINQ_IPV6, MAC_QINQ_IPV4_UDP, MAC_QINQ_IPV4_TCP, MAC_QINQ_IPV6_UDP, \
MAC_QINQ_IPV6_TCP. +* Enable QINQ switch filter for IPv4/IPv6, IPv4 + TCP/UDP in \
non-pipeline mode. +* Enable QINQ switch filter for IPv6 + TCP/UDP in pipeline mode.
+CVL support l4 for QinQ switch filter in DCF driver is by dst MAC + outer VLAN id + \
inner VLAN id + dst IP + dst port, and port can support as eth / vlan / vlan / IP / \
tcp|udp. +
+Prerequisites
+============+
+Hardware
+--------
+Supportted NICs: columbiaville_25g/columbiaville_100g
+
+Software
+--------
+dpdk: http://dpdk.org/git/dpdk
+scapy: http://www.secdev.org/projects/scapy/
+
+General Set Up
+--------------
+1. Copy specific ice package to /lib/firmware/updates/intel/ice/ddp/ice.pkg,
+ then load driver::
+
+ # cp ice_comms-1.3.31.0.pkg /lib/firmware/updates/intel/ice/ddp/ice.pkg
+ # rmmod ice
+ # insmod ice.ko
+
+2. Compile DPDK::
+
+ # CC=gcc meson --werror -Denable_kmods=True -Dlibdir=lib \
--default-library=static x86_64-native-linuxapp-gcc + # ninja -C \
x86_64-native-linuxapp-gcc -j 110 +
+3. Get the pci device id and interface of DUT and tester.
+
+ # ./usertools/dpdk-devbind.py -s
+
+ 0000:3b:00.0 'Ethernet Controller E810-C for SFP 1593' if=ens785f0 drv=ice \
unused=vfio-pci + 0000:af:00.0 'Ethernet Controller XXV710 for 25GbE SFP28 158b' \
if=ens260f0 drv=i40e unused=vfio-pci +
+4. Generate 2 VFs on PF0::
+
+ # echo 2 > /sys/bus/pci/devices/0000:3b:00.0/sriov_numvfs
+
+5. Get VF pci device id of DUT.
+
+ # ./usertools/dpdk-devbind.py -s
+
+ 0000:3b:01.0 'Ethernet Adaptive Virtual Function 1889' if=ens785f0v0 drv=iavf \
unused=vfio-pci + 0000:3b:01.1 'Ethernet Adaptive Virtual Function 1889' \
if=ens785f0v1 drv=iavf unused=vfio-pci +
+6. Set VF0 as trust::
+
+ # ip link set ens785f0 vf 0 trust on
+
+7. Bind the VF ports of DUT to dpdk::
+
+ # ./usertools/dpdk-devbind.py -b vfio-pci 3b:01.0 3b:01.1
+
+Test case
+========+
+Common Steps
+------------
+1. Launch the userland ``testpmd`` application on DUT as follows::
+
+ # ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0xf -n 4 -a 3b:01.0,capÜf -a \
3b:01.1 -- -i +
+2. Set verbose::
+
+ testpmd> set verbose 1
+
+3. Set fwd engine and start::
+
+ testpmd> set fwd rxonly
+ testpmd> start
+
+4. Show port info::
+
+ testpmd> show port info all
+
+ Check the VF0 driver is net_ice_dcf.
+
+#Non-pipeline mode
+
+Test Case 1: MAC_QINQ_IPV4
+---------------------------
+The test case enable QINQ switch filter for IPv4 in non-pipeline mode, and port can \
support as dst MAC + outer VLAN id + inner VLAN id + IPv4. +
+Test Steps
+~~~~~~~~~~
+1. Validate a rule::
+
+ testpmd> flow validate 0 ingress pattern eth dst is 00:11:22:33:44:55 / vlan \
tci is 2 / vlan tci is 1 / ipv4 src is 192.168.1.1 dst is 192.168.1.2 / end actions \
vf id 1 / end +
+ Get the message::
+
+ Flow rule validated
+
+2. Create a rule and list rules::
+
+ testpmd> flow create 0 ingress pattern eth dst is 00:11:22:33:44:55 / vlan tci \
is 2 / vlan tci is 1 / ipv4 src is 192.168.1.1 dst is 192.168.1.2 / end actions vf id \
1 / end +
+ Get the message::
+
+ Flow rule #0 created
+
+ Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH VLAN VLAN IPV4 => VF
+
+3. Send matched packet in scapy on tester, check the port 1 of DUT received this \
packet. +
+Tester::
+
+ >>> sendp([Ether(dst="00:11:22:33:44:55",type=0x8100)/Dot1Q(vlan=2,type=0x8100)/Dot1Q(vlan=0x1,type=0x0800)/IP(src="192.168.1.1", \
dst="192.168.1.2")/("X"*80)],iface="ens260f0",count=1) +
+DUT::
+
+ testpmd> port 1/queue 0: received 1 packets
+ src¤:BF:01:4D:6F:32 - dst :11:22:33:44:55 - type=0x8100 - length2 - nb_segs=1 - \
hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_NONFRAG - sw ptype: L2_ETHER_VLAN \
INNER_L2_ETHER_VLAN INNER_L3_IPV4 - l2_len - inner_l2_len=4 - inner_l3_len - \
Receive queue=0x0 + ol_flags: RTE_MBUF_F_RX_L4_CKSUM_GOOD \
RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN +
+4. Send mismatched packet in scapy on tester, check the port 1 of DUT could not \
receive this packet. +
+Tester::
+
+ >>> sendp([Ether(dst="00:11:22:33:44:33",type=0x8100)/Dot1Q(vlan=2,type=0x8100)/Dot1Q(vlan=0x1,type=0x0800)/IP(src="192.168.1.1", \
dst="192.168.1.2")/("X"*80)],iface="ens260f0",count=1) +
+ >>> sendp([Ether(dst="00:11:22:33:44:55",type=0x8100)/Dot1Q(vlan=1,type=0x8100)/Dot1Q(vlan=0x1,type=0x0800)/IP(src="192.168.1.1", \
dst="192.168.1.2")/("X"*80)],iface="ens260f0",count=1) +
+ >>> sendp([Ether(dst="00:11:22:33:44:55",type=0x8100)/Dot1Q(vlan=2,type=0x8100)/Dot1Q(vlan=0x2,type=0x0800)/IP(src="192.168.1.1", \
dst="192.168.1.2")/("X"*80)],iface="ens260f0",count=1) +
+ >>> sendp([Ether(dst="00:11:22:33:44:55",type=0x8100)/Dot1Q(vlan=2,type=0x8100)/Dot1Q(vlan=0x1,type=0x0800)/IP(src="192.168.1.3", \
dst="192.168.1.2")/("X"*80)],iface="ens260f0",count=1) +
+5. Destroy a rule and list rules::
+
+ testpmd> flow destroy 0 rule 0
+
+ Get the message::
+
+ Flow rule #0 destroyed
+
+ Check the flow list::
+
+ testpmd> flow list 0
+
+ Check the rule not exists in the list.
+ Send matched packets in step 3, check the packets are not to port 1.
+
+Test Case 2: MAC_QINQ_IPV6
+---------------------------
+The test case enable QINQ switch filter for IPv6 in non-pipeline mode, and port can \
support as dst MAC + outer VLAN id + inner VLAN id + IPv6. +
+Test Steps
+~~~~~~~~~~
+1. Validate a rule::
+
+ testpmd> flow validate 0 ingress pattern eth dst is 00:11:22:33:44:55 / vlan \
tci is 2 / vlan tci is 1 / ipv6 dst is CDCD:910A:2222:5498:8475:1111:3900:2020 / end \
actions vf id 1 / end +
+ Get the message::
+
+ Flow rule validated
+
+2. Create a rule and list rules::
+
+ testpmd> flow create 0 ingress pattern eth dst is 00:11:22:33:44:55 / vlan tci \
is 2 / vlan tci is 1 / ipv6 dst is CDCD:910A:2222:5498:8475:1111:3900:2020 / end \
actions vf id 1 / end +
+ Get the message::
+
+ Flow rule #0 created
+
+ Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH VLAN VLAN IPV6 => VF
+
+3. Send matched packet in scapy on tester, check the port 1 of DUT received this \
packet. +
+Tester::
+
+ >>> sendp([Ether(dst="00:11:22:33:44:55",type=0x8100)/Dot1Q(vlan=2,type=0x8100)/D \
ot1Q(vlan=0x1,type=0x86DD)/IPv6(dst="CDCD:910A:2222:5498:8475:1111:3900:2020")/("X"*80)],iface="ens260f0",count=1)
+
+DUT::
+
+ testpmd> port 1/queue 0: received 1 packets
+ src :00:00:00:00:00 - dst :11:22:33:44:55 - type=0x8100 - length2 - nb_segs=1 - \
hw ptype: L2_ETHER L3_IPV6_EXT_UNKNOWN L4_NONFRAG - sw ptype: L2_ETHER_VLAN \
INNER_L2_ETHER_VLAN INNER_L3_IPV6 - l2_len - inner_l2_len=4 - inner_l3_len@ - \
Receive queue=0x0 + ol_flags: RTE_MBUF_F_RX_L4_CKSUM_GOOD \
RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN +
+4. Send mismatched packet in scapy on tester, check the port 1 of DUT could not \
receive this packet. +
+Tester::
+
+ >>> sendp([Ether(dst="00:11:22:33:44:33",type=0x8100)/Dot1Q(vlan=2,type=0x8100)/D \
ot1Q(vlan=0x1,type=0x86DD)/IPv6(dst="CDCD:910A:2222:5498:8475:1111:3900:2020")/("X"*80)],iface="ens260f0",count=1)
+
+ >>> sendp([Ether(dst="00:11:22:33:44:55",type=0x8100)/Dot1Q(vlan=1,type=0x8100)/D \
ot1Q(vlan=0x1,type=0x86DD)/IPv6(dst="CDCD:910A:2222:5498:8475:1111:3900:2020")/("X"*80)],iface="ens260f0",count=1)
+
+ >>> sendp([Ether(dst="00:11:22:33:44:55",type=0x8100)/Dot1Q(vlan=2,type=0x8100)/D \
ot1Q(vlan=0x2,type=0x86DD)/IPv6(dst="CDCD:910A:2222:5498:8475:1111:3900:2020")/("X"*80)],iface="ens260f0",count=1)
+
+ >>> sendp([Ether(dst="00:11:22:33:44:55",type=0x8100)/Dot1Q(vlan=2,type=0x8100)/D \
ot1Q(vlan=0x1,type=0x86DD)/IPv6(dst="CDCD:910A:2222:5498:8475:1111:3900:2023")/("X"*80)],iface="ens260f0",count=1)
+
+5. Destroy a rule and list rules::
+
+ testpmd> flow destroy 0 rule 0
+
+ Get the message::
+
+ Flow rule #0 destroyed
+
+ Check the flow list::
+
+ testpmd> flow list 0
+
+ Check the rule not exists in the list.
+ Send matched packets in step 3, check the packets are not to port 1.
+
+Test Case 3: MAC_QINQ_IPV4_UDP
+------------------------------
+The test case enable QINQ switch filter for IPv4 + UDP in non-pipeline mode, and \
port can support as dst MAC + outer VLAN id + inner VLAN id + IPv4 + UDP. +
+Test steps
+~~~~~~~~~~
+1. Validate a rule::
+
+ testpmd> flow validate 0 ingress pattern eth dst is 00:11:22:33:44:55 / vlan \
tci is 2 / vlan tci is 1 / ipv4 / udp src is 50 dst is 23 / end actions vf id 1 / end \
+ + Get the message::
+
+ Flow rule validated
+
+2. Create a rule and list rules::
+
+ testpmd> flow create 0 ingress pattern eth dst is 00:11:22:33:44:55 / vlan tci \
is 2 / vlan tci is 1 / ipv4 / udp src is 50 dst is 23 / end actions vf id 1 / end +
+ Get the message::
+
+ Flow rule #0 created
+
+ Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH VLAN VLAN IPV4 UDP => VF
+
+3. Send matched packet in scapy on tester, check the port 1 of DUT received this \
packet. +
+Tester::
+
+ >>> sendp([Ether(dst="00:11:22:33:44:55",type=0x8100)/Dot1Q(vlan=2,type=0x8100)/D \
ot1Q(vlan=0x1,type=0x0800)/IP()/UDP(sportP,dport#)/("X"*80)],iface="ens260f0",count=1)
+
+DUT::
+
+ testpmd> port 1/queue 0: received 1 packets
+ src :00:00:00:00:00 - dst :11:22:33:44:55 - type=0x8100 - length0 - nb_segs=1 - \
hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_UDP - sw ptype: L2_ETHER_VLAN \
INNER_L2_ETHER_VLAN INNER_L3_IPV4 INNER_L4_UDP - l2_len - inner_l2_len=4 - \
inner_l3_len - inner_l4_len=8 - Receive queue=0x0 + ol_flags: \
RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD \
RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN +
+4. Send mismatched packet in scapy on tester, check the port 1 of DUT could not \
receive this packet. +
+Tester::
+
+ >>> sendp([Ether(dst="00:11:22:33:44:33",type=0x8100)/Dot1Q(vlan=2,type=0x8100)/D \
ot1Q(vlan=0x1,type=0x0800)/IP()/UDP(sportP,dport#)/("X"*80)],iface="ens260f0",count=1)
+
+ >>> sendp([Ether(dst="00:11:22:33:44:55",type=0x8100)/Dot1Q(vlan=1,type=0x8100)/D \
ot1Q(vlan=0x1,type=0x0800)/IP()/UDP(sportP,dport#)/("X"*80)],iface="ens260f0",count=1)
+
+ >>> sendp([Ether(dst="00:11:22:33:44:55",type=0x8100)/Dot1Q(vlan=2,type=0x8100)/D \
ot1Q(vlan=0x2,type=0x0800)/IP()/UDP(sportP,dport#)/("X"*80)],iface="ens260f0",count=1)
+
+ >>> sendp([Ether(dst="00:11:22:33:44:55",type=0x8100)/Dot1Q(vlan=2,type=0x8100)/D \
ot1Q(vlan=0x1,type=0x0800)/IP()/UDP(sportP,dport")/("X"*80)],iface="ens260f0",count=1)
+
+5. Destroy a rule and list rules::
+
+ testpmd> flow destroy 0 rule 0
+
+ Get the message::
+
+ Flow rule #0 destroyed
+
+ Check the flow list::
+
+ testpmd> flow list 0
+
+ Check the rule not exists in the list.
+ Send matched packets in step 3, check the packets are not to port 1.
+
+Test Case 4: MAC_QINQ_IPV4_TCP
+------------------------------
+The test case enable QINQ switch filter for IPv4 + TCP in non-pipeline mode, and \
port can support as dst MAC + outer VLAN id + inner VLAN id + IPv4 + TCP. +
+Test Steps
+~~~~~~~~~~
+1. Validate a rule::
+
+ testpmd> flow validate 0 ingress pattern eth dst is 00:11:22:33:44:55 / vlan \
tci is 2 / vlan tci is 1 / ipv4 / tcp src is 50 dst is 23 / end actions vf id 1 / end \
+ + Get the message::
+
+ Flow rule validated
+
+2. Create a rule and list rules::
+
+ testpmd> flow create 0 ingress pattern eth dst is 00:11:22:33:44:55 / vlan tci \
is 2 / vlan tci is 1 / ipv4 / tcp src is 50 dst is 23 / end actions vf id 1 / end +
+ Get the message::
+
+ Flow rule #0 created
+
+ Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH VLAN VLAN IPV4 TCP => VF
+
+3. Send matched packet in scapy on tester, check the port 1 of DUT received this \
packet. +
+Tester::
+
+ >>> sendp([Ether(dst="00:11:22:33:44:55",type=0x8100)/Dot1Q(vlan=2,type=0x8100)/D \
ot1Q(vlan=0x1,type=0x0800)/IP()/TCP(sportP,dport#)/("X"*80)],iface="ens260f0",count=1)
+
+DUT::
+
+ testpmd> port 1/queue 0: received 1 packets
+ src :00:00:00:00:00 - dst :11:22:33:44:55 - type=0x8100 - length2 - nb_segs=1 - \
hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_TCP - sw ptype: L2_ETHER_VLAN \
INNER_L2_ETHER_VLAN INNER_L3_IPV4 INNER_L4_TCP - l2_len - inner_l2_len=4 - \
inner_l3_len - inner_l4_len - Receive queue=0x0 + ol_flags: \
RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD \
RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN +
+4. Send mismatched packet in scapy on tester, check the port 1 of DUT could not \
receive this packet. +
+Tester::
+
+ >>> sendp([Ether(dst="00:11:22:33:44:33",type=0x8100)/Dot1Q(vlan=2,type=0x8100)/D \
ot1Q(vlan=0x1,type=0x0800)/IP()/TCP(sportP,dport#)/("X"*80)],iface="ens260f0",count=1)
+
+ >>> sendp([Ether(dst="00:11:22:33:44:55",type=0x8100)/Dot1Q(vlan=1,type=0x8100)/D \
ot1Q(vlan=0x1,type=0x0800)/IP()/TCP(sportP,dport#)/("X"*80)],iface="ens260f0",count=1)
+
+ >>> sendp([Ether(dst="00:11:22:33:44:55",type=0x8100)/Dot1Q(vlan=2,type=0x8100)/D \
ot1Q(vlan=0x2,type=0x0800)/IP()/TCP(sportP,dport#)/("X"*80)],iface="ens260f0",count=1)
+
+ >>> sendp([Ether(dst="00:11:22:33:44:55",type=0x8100)/Dot1Q(vlan=2,type=0x8100)/D \
ot1Q(vlan=0x1,type=0x0800)/IP()/TCP(sportP,dport")/("X"*80)],iface="ens260f0",count=1)
+
+5. Destroy a rule and list rules::
+
+ testpmd> flow destroy 0 rule 0
+
+ Get the message::
+
+ Flow rule #0 destroyed
+
+ Check the flow list::
+
+ testpmd> flow list 0
+
+ Check the rule not exists in the list.
+ Send matched packets in step 3, check the packets are not to port 1.
+
+#Pipeline mode
+
+Test Case 5: MAC_QINQ_IPV6_UDP
+------------------------------
+The test case enable QINQ switch filter for IPv6 + UDP in pipeline mode, and port \
can support as dst MAC + outer VLAN id + inner VLAN id + IPv6 + UDP. +
+Test Steps
+~~~~~~~~~~
+1. Validate a rule::
+
+ testpmd> flow validate 0 priority 0 ingress pattern eth dst is \
00:11:22:33:44:55 / vlan tci is 2 / vlan tci is 1 / ipv6 dst is \
CDCD:910A:2222:5498:8475:1111:3900:2020 / udp src is 50 dst is 23 / end actions vf id \
1 / end +
+ Get the message::
+
+ Flow rule validated
+
+2. Create a rule and list rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth dst is 00:11:22:33:44:55 \
/ vlan tci is 2 / vlan tci is 1 / ipv6 dst is CDCD:910A:2222:5498:8475:1111:3900:2020 \
/ udp src is 50 dst is 23 / end actions vf id 1 / end +
+ Get the message::
+
+ Flow rule #0 created
+
+ Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH VLAN VLAN IPV6 UDP => VF
+
+3. Send matched packet in scapy on tester, check the port 1 of DUT received this \
packet. +
+Tester::
+
+ >>> sendp([Ether(dst="00:11:22:33:44:55",type=0x8100)/Dot1Q(vlan=2,type=0x8100)/D \
ot1Q(vlan=0x1,type=0x86DD)/IPv6(dst="CDCD:910A:2222:5498:8475:1111:3900:2020")/UDP(sportP,dport#)/("X"*80)],iface="ens260f0",count=1)
+
+DUT::
+
+ testpmd> port 1/queue 0: received 1 packets
+ src :00:00:00:00:00 - dst :11:22:33:44:55 - type=0x8100 - length0 - nb_segs=1 - \
hw ptype: L2_ETHER L3_IPV6_EXT_UNKNOWN L4_UDP - sw ptype: L2_ETHER_VLAN \
INNER_L2_ETHER_VLAN INNER_L3_IPV6 INNER_L4_UDP - l2_len - inner_l2_len=4 - \
inner_l3_len@ - inner_l4_len=8 - Receive queue=0x0 + ol_flags: \
RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD \
RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN +
+4. Send mismatched packet in scapy on tester, check the port 1 of DUT could not \
receive this packet. +
+Tester::
+
+ >>> sendp([Ether(dst="00:11:22:33:44:33",type=0x8100)/Dot1Q(vlan=2,type=0x8100)/D \
ot1Q(vlan=0x1,type=0x86DD)/IPv6(dst="CDCD:910A:2222:5498:8475:1111:3900:2020")/UDP(sportP,dport#)/("X"*80)],iface="ens260f0",count=1)
+
+ >>> sendp([Ether(dst="00:11:22:33:44:55",type=0x8100)/Dot1Q(vlan=1,type=0x8100)/D \
ot1Q(vlan=0x1,type=0x86DD)/IPv6(dst="CDCD:910A:2222:5498:8475:1111:3900:2020")/UDP(sportP,dport#)/("X"*80)],iface="ens260f0",count=1)
+
+ >>> sendp([Ether(dst="00:11:22:33:44:55",type=0x8100)/Dot1Q(vlan=2,type=0x8100)/D \
ot1Q(vlan=0x2,type=0x86DD)/IPv6(dst="CDCD:910A:2222:5498:8475:1111:3900:2020")/UDP(sportP,dport#)/("X"*80)],iface="ens260f0",count=1)
+
+ >>> sendp([Ether(dst="00:11:22:33:44:55",type=0x8100)/Dot1Q(vlan=2,type=0x8100)/D \
ot1Q(vlan=0x1,type=0x86DD)/IPv6(dst="CDCD:910A:2222:5498:8475:1111:3900:2020")/UDP(sportP,dport")/("X"*80)],iface="ens260f0",count=1)
+
+5. Destroy a rule and list rules::
+
+ testpmd> flow destroy 0 rule 0
+
+ Get the message::
+
+ Flow rule #0 destroyed
+
+ Check the flow list::
+
+ testpmd> flow list 0
+
+ Check the rule not exists in the list.
+ Send matched packets in step 3, check the packets are not to port 1.
+
+Test case 6: MAC_QINQ_IPV6_TCP
+------------------------------
+The test case enable QINQ switch filter for IPv6 + TCP in pipeline mode, and port \
can support as dst MAC + outer VLAN id + inner VLAN id + IPv6 + TCP. +
+Test steps
+~~~~~~~~~~
+1. Validate a rule::
+
+ testpmd> flow validate 0 priority 0 ingress pattern eth dst is \
00:11:22:33:44:55 / vlan tci is 2 / vlan tci is 1 / ipv6 dst is \
CDCD:910A:2222:5498:8475:1111:3900:2020 / tcp src is 50 dst is 23 / end actions vf id \
1 / end +
+ Get the message::
+
+ Flow rule validated
+
+2. Create a rule and list rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth dst is 00:11:22:33:44:55 \
/ vlan tci is 2 / vlan tci is 1 / ipv6 dst is CDCD:910A:2222:5498:8475:1111:3900:2020 \
/ tcp src is 50 dst is 23 / end actions vf id 1 / end +
+ Get the message::
+
+ Flow rule #0 created
+
+ Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH VLAN VLAN IPV6 TCP => VF
+
+3. Send matched packet in scapy on tester, check the port 1 of DUT received this \
packet. +
+Tester::
+
+ >>> sendp([Ether(dst="00:11:22:33:44:55",type=0x8100)/Dot1Q(vlan=2,type=0x8100)/D \
ot1Q(vlan=0x1,type=0x86DD)/IPv6(dst="CDCD:910A:2222:5498:8475:1111:3900:2020")/TCP(sportP,dport#)/("X"*80)],iface="ens260f0",count=1)
+
+DUT::
+
+ testpmd> port 1/queue 0: received 1 packets
+ src :00:00:00:00:00 - dst :11:22:33:44:55 - type=0x8100 - length2 - nb_segs=1 - \
hw ptype: L2_ETHER L3_IPV6_EXT_UNKNOWN L4_TCP - sw ptype: L2_ETHER_VLAN \
INNER_L2_ETHER_VLAN INNER_L3_IPV6 INNER_L4_TCP - l2_len - inner_l2_len=4 - \
inner_l3_len@ - inner_l4_len - Receive queue=0x0 + ol_flags: \
RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD \
RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN +
+4. Send mismatched packet in scapy on tester, check the port 1 of DUT could not \
receive this packet. +
+Tester::
+
+ >>> sendp([Ether(dst="00:11:22:33:44:33",type=0x8100)/Dot1Q(vlan=2,type=0x8100)/D \
ot1Q(vlan=0x1,type=0x86DD)/IPv6(dst="CDCD:910A:2222:5498:8475:1111:3900:2020")/TCP(sportP,dport#)/("X"*80)],iface="ens260f0",count=1)
+
+ >>> sendp([Ether(dst="00:11:22:33:44:55",type=0x8100)/Dot1Q(vlan=1,type=0x8100)/D \
ot1Q(vlan=0x1,type=0x86DD)/IPv6(dst="CDCD:910A:2222:5498:8475:1111:3900:2020")/TCP(sportP,dport#)/("X"*80)],iface="ens260f0",count=1)
+
+ >>> sendp([Ether(dst="00:11:22:33:44:55",type=0x8100)/Dot1Q(vlan=2,type=0x8100)/D \
ot1Q(vlan=0x2,type=0x86DD)/IPv6(dst="CDCD:910A:2222:5498:8475:1111:3900:2020")/TCP(sportP,dport#)/("X"*80)],iface="ens260f0",count=1)
+
+ >>> sendp([Ether(dst="00:11:22:33:44:55",type=0x8100)/Dot1Q(vlan=2,type=0x8100)/D \
ot1Q(vlan=0x1,type=0x86DD)/IPv6(dst="CDCD:910A:2222:5498:8475:1111:3900:2020")/TCP(sportP,dport")/("X"*80)],iface="ens260f0",count=1)
+
+5. Destroy a rule and list rules::
+
+ testpmd> flow destroy 0 rule 0
+
+ Get the message::
+
+ Flow rule #0 destroyed
+
+ Check the flow list::
+
+ testpmd> flow list 0
+
+ Check the rule not exists in the list.
+ Send matched packets in step 3, check the packets are not to port 1.
+
--
2.25.1
[prev in list] [next in list] [prev in thread] [next in thread]
Configure |
About |
News |
Add a list |
Sponsored by KoreLogic