[prev in list] [next in list] [prev in thread] [next in thread]
List: cisco-nsp
Subject: RE: [nsp] full-duplex/cdp issues
From: "Martin, Christian" <CMartin () mercury ! balink ! com>
Date: 2000-04-28 14:03:43
[Download RAW message or body]
We have run into this issue - it is a cosmetic bug. It is fixed in
12.07DC...
NRP1#sh int f0/0/0
FastEthernet0/0/0 is up, line protocol is up
Hardware is AmdFE, address is 0050.736f.9109 (bia 0050.736f.9109)
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 5/255, rxload 30/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, 100BaseTX/FX
NRP1 uptime is 3 days, 5 hours, 1 minute
System returned to ROM by reload at 04:54:33 EDT Tue Apr 25 2000
System restarted at 04:59:29 EDT Tue Apr 25 2000
System image file is "flash:c6400r-g4p5-mz_120-7_DC.bin
regards,
chris
> -----Original Message-----
> From: Layer 2 Prostitute [mailto:ducktape@puck.nether.net]
> Sent: Thursday, April 27, 2000 2:30 PM
> To: cisco-nsp@puck.nether.net
> Subject: [nsp] full-duplex/cdp issues
>
>
> We have an AS6400 here at my company, many actually. The
> issue that I'm
> having is that on interface fa0/0/0 which is our transit port
> it comes up
> as half duplex when it should be full. The NRP's are connected to
> 6509 CATS. We've turned off auto negotiate on both the cats and the
> NRP cards, bounced the ports and the problem still exists. This is
> happening on a number of the NRP cards. All of our NRP cards
> are running
> c6400r-g4p5-mz.120-5.DC. Our cats are using the WS-X6K-SUP1A-2GE for
> hardware and 5.3(5a)CSX or 5.4(1) for catos. We've noticed that when
> running 5.3(5a)CSX the cats are generating
> %CDP-4-DUPLEXMISMATCH:Full/half
> duplex mismatch detected errors and the NRP cards are doing
> the same, this
> is with CDP enabled. When running 5.4(1) on the cat and CDP
> is set for
> version2 we get the same errors. However when CDP is set for version1
> using 5.4(1) on the cat the problem goes away. 5.3(5a)CSX
> does not allow
> you to choose between v1 and v2. I disabled CDP on the cats in a pop
> that is running 5.3(5a)CSX and the duplex mismatch errors are
> still there
> and the interface on the NRP still shows up as being half
> instead of full
> *sigh*. Here's the catch to this issue, on the the cats running
> 5.3(5a)CSX not all the cards show up as half duplex, some
> show up properly
> negotiated to full *sigh*. The NRP cards only support CDPv1.
> Has anyone
> else run across this issue?
>
> Bob Davidovich
> IP Engineering - Northpoint Communications
>
[prev in list] [next in list] [prev in thread] [next in thread]
Configure |
About |
News |
Add a list |
Sponsored by KoreLogic