[prev in list] [next in list] [prev in thread] [next in thread] 

List:       aix-l
Subject:    Re: Setting up a Modem on an H70
From:       Basim Chafik <basimc () INVERA ! COM>
Date:       2000-05-30 15:42:22
[Download RAW message or body]


Gary,

Change the protocol to xon instead of rts and forcedcd on tty1.

Basim Chafik

Senior Technology Consultant
IBM Certified Specialist - AIX Support
Invera


-----Original Message-----
From: Gary Luther [mailto:GLuther@MHESAC.ORG]
Sent: Tuesday, May 30, 2000 11:26 AM
To: AIX-L@pucc.Princeton.EDU
Subject: Setting up a Modem on an H70


This is probably a no-brainer.......but then again.....

I had a 28.8 modem hooked up to my H70 for dial-in. Everything worked just
fine.

So, the other day I connected a 56K US Robotics Sportster Fax Modemto get a
little faster dial-in access.
Can't get the little sucker to work.

When I do a

pdisable tty1
cu -l tty1

I immediately get  a

connected

Lost Carrier.

The connection is ended.

The following is my /usr/lib/uucp/Devices entries:

Direct tty1 - Any direct

My switch settings are:

S
1  ^  DTR
2  ^  Verbal Output
3  V  Display Results code
4  ^  Echo off
5  ^  Auto Answer
6  ^  Carrier Detect
7  V  Load Factory defaults
8  V  Smart mode

^ means switch is up
V means switch is down.

My smitty settings are as follows:

  TTY                                                 tty1
  TTY type                                            tty
  TTY interface                                       rs232
  Description                                         Asynchronous Terminal
  Status                                              Available
  Location                                            01-S3-00-00
  Parent adapter                                      sa2
  PORT number                                        [0]
+
  Enable LOGIN                                        share
+
  BAUD rate                                          [38400]
+
  PARITY                                             [none]
+
  BITS per character                                 [8]
+
  Number of STOP BITS                                [1]
+
  TIME before advancing to next port setting         [0]
+#
  TERMINAL type                                      [vt100]
  FLOW CONTROL to be used                            [rts]
+
  OPEN DISCIPLINE to be used                         [dtropen]
+
  STTY attributes for RUN time
[hupcl,cread,brkint,icr> +
  STTY attributes for LOGIN                          [hupcl,cread,echoe,cs8]
  LOGGER name                                        []
  STATUS of device at BOOT time                      [available]
+
  REMOTE reboot ENABLE                                no
+
  REMOTE reboot STRING                               [#@reb@#]
  TRANSMIT buffer count                              [16]
+#
  RECEIVE trigger level                              [3]
+#
  STREAMS modules to be pushed at OPEN time          [ldterm]
+
  INPUT map file                                     [none]
+
  OUTPUT map file                                    [none]
+
 CODESET map file                                   [sbcs]
+




=============================
Two farmers, each claimed to own a certain cow. While one pulled on
it's head and the other on the tail, the cow was milked by a lawyer.

Remember, your body is a temple; however, it's also your dancehall
and bowling alley (Dharma Montgomery)
=============================
WORK:                      (406) 444-0631
Gary K. Luther, System Administrator
SAF/MHESAC
2500 Broadway
Helena, MT 59602-3104
gluther@safmt.org
=============================
HOME:                      (406) 227-2240
3838 Beechnut St. #1
E. Helena, MT 59635
gkluther@operamail.com
=============================

[prev in list] [next in list] [prev in thread] [next in thread]